Kreg Owners' Community

All Product Reviews (241)

Kreg Deck Jig -One Word

Used my Kreg Deck Jig for the first time the other day. 

Replaced all the wood deck boards on my deck.

I've got one word for the Deck Jig --- SLICK

Added by Fins59 on May 11, 2013 at 12:10pm — 1 Comment

Byrd Shelix Journel Head (installed on 15inch Jet)

Finally got the Byrd Shelix Journal Head installed on my planer.  Ordered it through Holbren, Sawmill Creek members get 10% off, SMC10 is the code.  First off, I installed the head by myself and it was completely painless, I was shocked to say the least.  I will say that I am thrilled that I had Byrd install new bearings for me and I would suggest if you are thinking of upgrading that you do the same thing.  I also ordered a new gasket for the gear box while I was at it, I would recommend…

Continue

Added by justin waldron on May 5, 2013 at 7:23pm — 4 Comments

Rikon 10-345 18" bandsaw

I ordered this 18" Rikon through Highland Woodworking about 3 weeks ago.  Highland had it on sale for $999, shipping was $125 and I ordered a mobile base at the same time, so all in all $1200 delivered to my door.  I will start with the only 2 low points…

Continue

Added by justin waldron on March 6, 2013 at 8:07am — 23 Comments

Kreg Universal Drawer Slide Mounting Jig & Brackets Review

One of my favorite toys is my Kreg Drawer Slide Jig.  There are actually two jigs that you'll want to use to help you install a drawer.  These two jigs really compliment each other, and make completing drawer installs a snap.  I picked up both jigs from Amazon for a really reasonable…

Continue

Added by Daris R. on January 30, 2013 at 12:30am — 4 Comments

Kreg Rip Cut

I was fortunate enough to receive a Kreg Rip Cut last spring as they were first shipping but didn't begin using it until this fall.  Initially I attempted to attach the Rip Cut to my Worm Drive Mag framing saw.  The base of that saw has a lip that is great for pushing dust out of the way but makes it difficult to attach the Rip Cut, so I got out my back up saw- an older…

Continue

Added by Kevin Bergstrom on January 29, 2013 at 5:30pm — 12 Comments

Kreg sawdust jig relief

We have found the holes in the three hole block imeed the discharge of sawdust during the final depth of the drill bit. We do a lot of hard wood work which appears to be when this plugging of the discharge holes occures. We were wondering if anyone else has this problem and if a solution would be to lower the relief holes to allow sawdust discharge nearer the base of the block.

Added by James Lindemulder on January 25, 2013 at 12:33pm — 5 Comments

My new Kreg tool box

I received a Kreg tool box for Christmas this year.  I love it.  I now have a place to keep all of my Kreg clamps, extra drill bits, extra driver bits, and even my Kreg tool in the bottom of the tool box.  I love the removable trays for screw in the top of the box and the see thru lid.  I love the way that the top is supported with the legs in the back when you lift the top lid to get to the bottom.  The only way this box could have been better is is the bottom was a little deeper but it's…

Continue

Added by David Niebeling on January 12, 2013 at 7:06pm — 5 Comments

Square Cut is not square

I bought a Square Cut to use with my circular saw.



Just before making the first cut I decided to check the angle, and unfortunately the “right angle” came out not to be exact. At first I became very frustrated and was ready to throw it away on the upper shelve. But, as several cuts had to be made at the time, I solved the problem by sticking several pieces of…

Continue

Added by Misha on January 11, 2013 at 1:13pm — 10 Comments

makita rpo700cx3 router

I purchased the 1 1/4 hp , trim router kit , and used it several times, while making my wife a jewlery box, i got plans from norm abrams site, and loved the router in the building of the jewlery box, i recommend that if you are looking for a (GREAT) trim router , too buy it, got at factory authourized outlet for $228.00  and i love it, it's a great add to my work shop....   and , the new yankee workshop site is a great place to get plans for projects and plans for jigs , that make working in…

Continue

Added by steven michaud on December 27, 2012 at 7:36am — No Comments

Triton trb001router

Hi this is a review of the triton 2000watt router.I think its the most innovative router i have come across.The triton has 3 modes of depth setting,including a winder handle facility for table mounting.It is variable speed and loses no momentum under load.A big bonus for me its very quiet in use .Overall i give it 9 out of 10.

Added by michael evans on November 25, 2012 at 1:01pm — 3 Comments

MAKITA mac5200 copressor

went online to find the best price for a good compressor, i was looking at the dewalt compressor, read alot of reviews on all kinds of compressors, and decided on the mac5200, recieved it from homedepot , the other day, and brought it to the construction site yesterday, for the first time, i liked it's performance alot, it is built tough, and anxious to see it in action, when we start sheeting the 32 x 100 foot building , we are constructing.  all in all really pleased so far..   homedepot…

Continue

Added by steven michaud on November 11, 2012 at 7:35am — No Comments

Kreg RipCut

First off I have to say just how much I LOVE my rip cut!! It was easy to set up, so very easy to use and I love the fact that I don't have to ask my hubby to come out and help me when I need to rip down my sheet goods! The only thing that I can say bad about it is that the guide on the left could be a bit longer so that when you get to the end of your cut you are still staying true to the cut itself.  After a couple dozen cuts I've gotten to where I can keep that plane going, but it's still…

Continue

Added by Tracy Smith on October 30, 2012 at 8:59am — 6 Comments

kreg benchtop router table

Hi all just road tested my kreg router table , i give it 8out of 10.

                                  PRO/s

Its well made with a nice flat table.

The insert plate top notch quality.

The plate levellers are a great idea.

Dust extraction via the fence seems to work well.

Assembly fairly simple good instructions.

                                 CON/s

Table should come with hold down brackets.

No nvr switch had too take off my old…

Continue

Added by michael evans on October 14, 2012 at 10:44am — 7 Comments

Kreg Shelf Pin Jig Review

The Kreg Shelf Pin Jig is an excellent jig to add your woodworking collection.  I've done the "make your own" pegboard type of jig.  The problem is you cut it down to size and it seems like you never get it right the first time.  When you do finally get it right it still feels a little off…

Continue

Added by Daris R. on September 17, 2012 at 8:30am — 2 Comments

My Review of WoodRiver Deluxe Scraper Set

div class="hreview"div class="item"pa href="http://www.woodcraft.com/Product/2020573/23361/WoodRiver-Deluxe-Scraper-Set.aspx"Originally submitted at Woodcraft/a/pdivp style="margin-top:0"/p/diva href="http://www.woodcraft.com/Product/2020573/23361/WoodRiver-Deluxe-Scraper-Set.aspx" style="display: none;" class="url fn"span class="fn"WoodRiver Deluxe Scraper Set/span/a/divbr clear="left"pstrong class="summary"Very happy with purchase/strong/pdivBy strongJoe/strong from strongBridgewater,… Continue

Added by Joseph M. on August 7, 2012 at 12:02pm — No Comments

Jet 1 1/2 hp Shaper

What an awesome little machine!  The machine comes with a 1/4 and 1/2 inch collet for router bits and a 1/2 and 3/4 inch spindle for shaper cutters.  Changing of the bits are extremely easy from a lock on the underside of the table, belt tensioning is a dream.  This is a little…

Continue

Added by justin waldron on August 1, 2012 at 6:44am — 13 Comments

Jet 15 inch planer

I have been using a Dewalt 735 for the past 3 years and knew I needed to upgrage to something with more power and I finally did, this Jet is 15 inches and 3 HP.  I've read many reviews on many planers and they are all mixed.  The only thing I miss from…

Continue

Added by justin waldron on August 1, 2012 at 6:38am — 4 Comments

Kreg Multi-Mark

Yeah, I know what you're thinking and you're partly right.  Why am I reviewing a glorified ruler?   Well there is a little bit more to it than that.  I have a couple of combo squares that I regularly use, and one of them broke a few weeks ago.  Recently, I've turned into a…

Continue

Added by Daris R. on July 11, 2012 at 3:00pm — 7 Comments

I Just Keeps On Giving....

Wow,

The Kreg Mastery Set delivers again.

Major mess under my desk in my home office.

Power supplies, external hard drives, Power bars(x2), and cords.

Have 4 Pieces of the modular desk I purchased 5 years ago behind the desk.

Pull the table saw out(10min)

Cut 2 pieces 11" wide x 33" long x 1" thick for extra desk pieces(15min)

Set up Kreg Jig for 1" stock(2min+-)

Drilled 8 pocket holes total(10min)

Screws Kreg SPS-C1 Course…

Continue

Added by Melton Antypowich on July 7, 2012 at 12:44am — No Comments

Project #1

Just starting my project. nothing to report at this time

Added by Luan H. Hamit on June 27, 2012 at 2:49pm — 1 Comment

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Just Assembled Adaptive Cutting System 1 Reply

I purchased the ACS directly from Kreg 2 weeks ago. This morning I finished the assembly with the exception of installing the measuring tapes. The assembly took me about 4 hours, between reading the manual, watching videos and sipping coffee. I'm…Continue

Tags: ACS, System, Cutting, Adaptive

Started by Robert P Trower in Other Kreg® Products. Last reply by KregRep Aug 13.

Problem with automax project clamp and bench clamp 1 Reply

I cannot get either clamp to face clamp a 2" x 4". Is there a fix for this?Continue

Started by Christian Bookter in Beginners' Zone. Last reply by KregRep Aug 9.

Product Reviews

K5 Review

I really like the k5 it is faster to change from different size of screws. I hesitated to update because of some of the reviews about the dust collection hook up. That to me one of the improvements it works perfect no dust to cleanup .…

Continue

Posted by Gary roofner on April 5, 2019 at 10:02am

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm — 1 Comment

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_