Kreg Owners' Community

General Woodworking (624)

Featured Discussions

Clamping & assembly worktop

Make your own shop-made clamping & assembly workbench. ........ Kreg Klamp Track locate several of these units, banked side-by-side, t…

Started by Ken DargaLatest Reply

Discussions Replies Latest Activity

Sanding question?

i am refinnishing a table that has round legs.  what is the easiest way to sand the legs?

Started by Matthew Brown

15 Jan 3
Reply by brinda Ashley

Purchase a bandsaw

I have been looking to find a bandsaw found a saw on Craigs list today. It's a 12" electronic craftsman band saw  has a big stand and big t…

Started by Gary roofner

6 Jan 3
Reply by brinda Ashley

Bunk Beds, Kreg screws strong enough?

I am going to build a low loft bunk bed for my 5 year old. Hopefully he can use for many years.  I have a seen a few nice plans on the foru…

Started by Mack

20 Nov 14, 2018
Reply by Sam Poulson

What hinge should I use?

I am building a cabinet / closet that is 30 inches wide.  I was going to use 2 doors 15 inches wide from 3/4 inch plywood.  My guess is the…

Started by Lynn Greff

5 Sep 29, 2018
Reply by Edward Weitsman

Pocket screws to attach table tops

Hello, I have made a whole set of Mission tables, and use pocket screws to attach the tops, this was before I actually knew a lot about woo…

Started by Joe L

3 Sep 28, 2018
Reply by Michael Lew

Substitute for right angle clamps

Tomorrow I will begin constructing the Shop Vacuum Cart found on the Kreg "Build Something," website. https://www.buildsomething.com/plans/

Started by Michael Meyer

12 Aug 12, 2018
Reply by Ed McGugan

coffin for animals

Hello, I'm looking for plans for a coffin for small animals (cat size)... basic model. Any ideas? Thank you for your time. Manny

Started by Manuel Vasquez

2 Jul 3, 2018
Reply by Manuel Vasquez

Bench dog holes

Good day everyone; my name is Bruno from San Diego, CA. Building dog holes on a bench top; looking for info specific on proper set up, hole…

Started by Bruno

4 Mar 26, 2018
Reply by Glen S

Bench dog holes

Good day everyone; my name is Bruno from San Diego, CA. Building dog holes on a bench top; looking for info specific on proper set up, hole…

Started by Bruno

3 Mar 24, 2018
Reply by Brad Martin

What is it?

I am trying to determine the name of a piece of specialty hardware. It consist of a screw at one end and a bolt at the other. You screw the…

Started by Michael Meyer

4 Mar 4, 2018
Reply by Scott

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Kreg Accu-Cut and Rip-Cut 4 Replies

First off tried to mention all this to Kreg via Email and just because I live outside the USA seems that the system does not work as they say phone number invalid, which is not.OK bought a Accu-Cut and set it up no problems there worked OK both…Continue

Started by Kenneth J Hunt in Other Kreg® Products. Last reply by Kenneth J Hunt on Wednesday.

Router bits 4 Replies

Tungsten carbide? Skill level is beginning woodworker

Started by MINICOOPERUSAF in Beginners' Zone. Last reply by Tim Grace Jan 14.

R3 part

hi all can anybody help got r3 for Xmas and I have noticed that the gray tabs are different think somebody  in assembly was talking the piss day and I have 1 metric side and imperial side so they don’t match up hellllp plzericContinue

Started by Eric Kershaw in Beginners' Zone Jan 8.

Having issues with K5 5 Replies

I watched the setup videos, searched for information and spent half a day and can not get the clamp to hold.i tightened up the screws underneath in various stages up to fully tightened, makes no difference.I do not get the two clicks and I can slide…Continue

Started by Todd Caldwell in Beginners' Zone. Last reply by Glen S Jan 7.

Product Reviews

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 4 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am

Kreg Foreman

I have built many kitchens and finally decided to buy the Foreman, because my latest kitchen consisted of 28 cabinets and I was over my hand hurting from all the drilling, moving the clamp etc., it seemed like a smart choice.

The…

Continue

Posted by justin waldron on January 8, 2018 at 4:05am — 2 Comments

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_