Kreg Owners' Community

Connect with Kreg!



Latest Activity

Gary roofner replied to james wilhelm's discussion 'New plug cutter!!'
"I found out the problem cutting the plugs free my main setup. It was because the support was about 1/16 above the deck of the kreg jig . This translates into cutting a shorter plug. I have an older k4 that I have dedicated plug cutting. I am…"
7 hours ago
Jerry Morris posted a photo
8 hours ago
Duane Dickinson posted a discussion

Onion and Tater bin

I was wondering if anyone knew the ventilation requirements to make a tater and onion bin?
12 hours ago
carol posted a discussion

using shelf pin drilling jig

building a custom closet and before i begin, ordered both the 1/4" and 5mm jigs to try out.on plywood, using a slower speed, i get nice, clean holes with very little to no tearout. but the solid wood (pine), on either slow speed or high, i'm getting…See More
15 hours ago
Tim Grace replied to Brian fleming's discussion 'Kreg setting for 3x3'
"Set the jig to the actual dimension of the wood you are drilling into.   In this case, I would attach the apron to the legs (and top?) using the apron's actual thickness (you state 1", is it actually ¾"? )  The jig…"
16 hours ago
Glen S commented on Jeff Chaffin's photo
Thumbnail

armiore

"How nice is that!! I love knotty pine too & you did a fantastic job Jeff!!"
yesterday
Glen S replied to Brian fleming's discussion 'Card table'
"The aprons & legs are on a vertical plane. Top is on a horizontal plane. Light play off these planes differently. The apron for example will be in the shadows of the overhanging top. Make a quick mock up with some scraps & stain both pieces…"
yesterday
Glen S replied to Tom's discussion 'Hardwood joints'
"Beeswax the threads."
yesterday
 

Click a Button to Navigate the Kreg Owners' Community

Photos

Loading…
  • Add Photos
  • View All

Take your Kreg Joinery projects to the next level.

With the Custom Pocket-Hole Plug Cutter, you can use pocket-hole joinery virtually anywhere — even in places that show prominently on your project — by hiding the pocket holes with perfectly matched plugs that you create from your from any wood you desire.

Free Plan of the Month: Miter Saw Dust Hood

Your free plan will open when you click on the image above.

Install Knobs and Pulls with Easy, Repeatable Accuracy

Whether you’re updating your cabinets or building a project from scratch, the new Kreg Cabinet Hardware Jig makes it easy to install new knobs and pulls easily and consistently every time. Adjustable hardened-steel drill guides, a movable edge guide, and built-in measuring scales ensure simple, repeatable accuracy. 

Make Cabinet Door Installation Easy!

The all-new Kreg Concealed Hinge Jig takes the guesswork out of installing cabinet doors using concealed hinges. This economical, easy-to-use jig ensures accurate hinge alignment, so you can install doors that fit great and work well. Plus, the Concealed Hinge Jig works with an ordinary drill and the included carbide-tipped bit.

Install Drawer Slides the Fast, Easy Way


Installing drawer slides doesn’t have to be difficult. The new Kreg Drawer Slide Jig eliminates the guesswork and makes the process easy by holding the slides—and the drawer box—in perfect position, leaving both hands free to attach the slides. 

Forum

Onion and Tater bin

I was wondering if anyone knew the ventilation requirements to make a tater and onion bin?

Started by Duane Dickinson in Miscellaneous 12 hours ago.

using kreg shelf pin drilling jig

building a custom closet and before i begin, ordered both the 1/4" and 5mm jigs to try out.on plywood, using a slower speed, i get nice, clean holes with very little to no tearout. but the solid wood (pine), on either slow speed or high, i'm getting…Continue

Tags: jig, drilling, pin, shelf

Started by carol in Other Kreg® Products 15 hours ago.

Kreg setting for 3x3 1 Reply

Question i need pocket holes to join my table legs and apron . What setting would I set my kre jig up for a 3x3 I will be using 1 inch thick oak for the apron. And I will beef up the top of it with boards running across

Started by Brian fleming in Beginners' Zone. Last reply by Tim Grace 16 hours ago.

Glue 3 Replies

Question I put together a 4x4 foot table with 1 inch red oak barn wood all if it went through a jointer before hand. I used pocket screws only and yes it took a ton of screws and I didn't get glue I was able to upright the table and it was solid one…Continue

Started by Brian fleming in Beginners' Zone. Last reply by Glen S yesterday.

Store and organize your Kreg Screws and other hardware.

Kreg Hardware Containers are the perfect solution for storing and organizing all kinds of loose hardware. These handy containers (available in Small and Largeare the same durable, resealable, reusable containers that are used to package Kreg Screws.

Kreg Clamps with Automaxx® Auto-Adjust Technology

Kreg Clamps with Automaxx® Technology make clamping faster and easier than ever by adjusting automatically to clamp materials that are thick, thin, or in between. You’ll find Automaxx® on a wide variety of Kreg Clamps, including the Right Angle ClampWood Project Clamps, Bench ClampsBar Clamps, the Clamp Vise, and Kreg Clamp Table.

Turn your custom projects into professional-looking plans to inspire others!

1. Join BuildSomething   2. Upload a Plan   3. Get a FREE T-shirt!

 
 
 

Need Help?

Technical Support is happy to help via phone or email. Call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 

Or, post a discussion in the Forums any time.

Videos

  • Add Videos
  • View All

Product Reviews

Laguna 14BX Band Saw

Posted by Tim Grace on December 20, 2016 at 1:52am — 1 Comment

Kreg mobile project center

Posted by Gary roofner on November 21, 2016 at 10:00am — 4 Comments

6" bench clamp

Posted by Steven Lee on November 14, 2016 at 9:30am

© 2017   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_