Kreg Owners' Community

Brad Martin's Discussions (33)

Discussions Replied To (33) Replies Latest Activity

"I use a small square to check when I adjust something on both my table saw and mitre…"

Brad Martin replied Dec 18, 2018 to Measuring angle of table saw blade

4 on Monday
Reply by Tim Grace

"You can buy 1 1/2 Blue Kote in Australia so you should be able to get them too. I w…"

Brad Martin replied Dec 18, 2018 to Can I use standard Kreg screws for an exterior tabletop I'm building?

1 Dec 18, 2018
Reply by Brad Martin

"If you have an offcut I would do a test hole so you can check you not going to go th…"

Brad Martin replied Dec 1, 2018 to Edge Joining 2" Boards

4 Dec 17, 2018
Reply by brian lazenby

"I would use the square pattern dog holes in my bench with a dog fence ( could use Kr…"

Brad Martin replied Sep 2, 2018 to 45 degree angles

1 Sep 2, 2018
Reply by Brad Martin

"That thread has gone walk about. I have gone with edge fitting and then offsetting…"

Brad Martin replied Aug 3, 2018 to Kreg Clamp Track Location on Workbench

4 Aug 3, 2018
Reply by Brad Martin

"I have a composite decking floor in a garden shed fixed to steel, even out of direct…"

Brad Martin replied Jul 16, 2018 to Can deck jig fastening limit heat expansion?

2 Jul 23, 2018
Reply by Ed Henderson

"Since it has been deleted from here, Pinterest may be your friend. Assembly Table…"

Brad Martin replied Jun 14, 2018 to Missing clamping table project

6 Jul 6, 2018
Reply by Brandon B.

"Tried an offcut and a clamp?"

Brad Martin replied May 22, 2018 to kreg production stop extension

1 May 22, 2018
Reply by Brad Martin

"Looking good. You might want some clamp blocks too."

Brad Martin replied May 22, 2018 to Layout/Project Setup Table

11 May 22, 2018
Reply by Brad Martin

"I used the Kreg Clamp Track and clamp blocks with Rockler T-track to use their inlin…"

Brad Martin replied May 13, 2018 to Layout/Project Setup Table

11 May 22, 2018
Reply by Brad Martin

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Kreg Accu-Cut and Rip-Cut 4 Replies

First off tried to mention all this to Kreg via Email and just because I live outside the USA seems that the system does not work as they say phone number invalid, which is not.OK bought a Accu-Cut and set it up no problems there worked OK both…Continue

Started by Kenneth J Hunt in Other Kreg® Products. Last reply by Kenneth J Hunt yesterday.

Router bits 4 Replies

Tungsten carbide? Skill level is beginning woodworker

Started by MINICOOPERUSAF in Beginners' Zone. Last reply by Tim Grace on Monday.

R3 part

hi all can anybody help got r3 for Xmas and I have noticed that the gray tabs are different think somebody  in assembly was talking the piss day and I have 1 metric side and imperial side so they don’t match up hellllp plzericContinue

Started by Eric Kershaw in Beginners' Zone Jan 8.

Having issues with K5 5 Replies

I watched the setup videos, searched for information and spent half a day and can not get the clamp to hold.i tightened up the screws underneath in various stages up to fully tightened, makes no difference.I do not get the two clicks and I can slide…Continue

Started by Todd Caldwell in Beginners' Zone. Last reply by Glen S Jan 7.

Product Reviews

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 4 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am

Kreg Foreman

I have built many kitchens and finally decided to buy the Foreman, because my latest kitchen consisted of 28 cabinets and I was over my hand hurting from all the drilling, moving the clamp etc., it seemed like a smart choice.

The…

Continue

Posted by justin waldron on January 8, 2018 at 4:05am — 2 Comments

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_