Kreg Owners' Community

Obviously for pocket joinery having the wood pieces cut square is critical to having a good joint.  This minimizes the likelihood of overtightening screws, as well giving a stronger more attractive joint.  Does anyone routinely measure the angle of their table saw blade, using something like a Wixey digital angle gauge?  Is it worth the $20-30 to get one?

Views: 170

Reply to This

Replies to This Discussion

I use a small square to check when I adjust something on both my table saw and mitre saw. My mitre saw was a bit off from new. I have a digital square/level but that is a bit too big and a bit painful to set at 90.

I use a digital angle gauge for my table saw, it also works great leveling my travel trailer. 

As for the saw, the built in marker never stays in place so I can't count on it. There are also times when I'm cutting odd angles like between 53-68 degrees, not many angle gauges can measure it accurately enough. I also use it to check the angle on my miter saw when doing crown molding to make sure I've got good sharp cuts.

I have the Wixey & use it to set any angle except 45 & 90. I have trusted squares for that. I played around with 22 1/2 angles on 2" wide by 12"L & made a very nice glueable cylinder.

I use the Wixey gauge anytime I adjust the angle of the blade. It's worth every penny I paid for it.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Kreg Accu-Cut and Rip-Cut 4 Replies

First off tried to mention all this to Kreg via Email and just because I live outside the USA seems that the system does not work as they say phone number invalid, which is not.OK bought a Accu-Cut and set it up no problems there worked OK both…Continue

Started by Kenneth J Hunt in Other Kreg® Products. Last reply by Kenneth J Hunt on Wednesday.

Router bits 4 Replies

Tungsten carbide? Skill level is beginning woodworker

Started by MINICOOPERUSAF in Beginners' Zone. Last reply by Tim Grace on Monday.

R3 part

hi all can anybody help got r3 for Xmas and I have noticed that the gray tabs are different think somebody  in assembly was talking the piss day and I have 1 metric side and imperial side so they don’t match up hellllp plzericContinue

Started by Eric Kershaw in Beginners' Zone Jan 8.

Having issues with K5 5 Replies

I watched the setup videos, searched for information and spent half a day and can not get the clamp to hold.i tightened up the screws underneath in various stages up to fully tightened, makes no difference.I do not get the two clicks and I can slide…Continue

Started by Todd Caldwell in Beginners' Zone. Last reply by Glen S Jan 7.

Product Reviews

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 4 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am

Kreg Foreman

I have built many kitchens and finally decided to buy the Foreman, because my latest kitchen consisted of 28 cabinets and I was over my hand hurting from all the drilling, moving the clamp etc., it seemed like a smart choice.

The…

Continue

Posted by justin waldron on January 8, 2018 at 4:05am — 2 Comments

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_