Kreg Owners' Community

Brad Martin
  • Adelaide
  • Australia
Share on Facebook
Share

Brad Martin's Friends

  • Todd J Michalec12@gmail.com
 

Brad Martin's Page

Latest Activity

Brad Martin replied to Ada Berry's discussion '45 degree angles'
"I would use the square pattern dog holes in my bench with a dog fence ( could use Kreg dogs also ) and Kreg inline clamps. Ratio to get to 45D is 1:1 so say 2 holes across and 2 holes up to place a dog and 5 holes across and 5 holes up to place the…"
Sep 2
Brad Martin replied to art bartolomeo's discussion 'Kreg Clamp Track Location on Workbench'
"That thread has gone walk about. I have gone with edge fitting and then offsetting the 16mm melamine side to avoid the screw heads fouling it. I also have a t-trak so I can clamp boxes that runs aprox 100mm from the clamp blocks. Works great if…"
Aug 3
Brad Martin replied to Glenn Scott's discussion 'Can deck jig fastening limit heat expansion?'
"I have a composite decking floor in a garden shed fixed to steel, even out of direct sun and most of the weather it still contracts and expands. While the deck jig puts the boards in nicely and the screws have a good hold and I think my shed would…"
Jul 16
Brad Martin replied to Brandon B.'s discussion 'Missing clamping table project'
"Since it has been deleted from here, Pinterest may be your friend. Assembly Table You need to scroll down near the end of that page to see some more details. BTW it is not my page either."
Jun 14
Brad Martin replied to Pat Meeuwissen's discussion 'kreg production stop extension'
"Tried an offcut and a clamp?"
May 22
Brad Martin replied to Todd J Michalec12@gmail.com's discussion 'Layout/Project Setup Table'
"Looking good. You might want some clamp blocks too."
May 22
Brad Martin replied to Todd J Michalec12@gmail.com's discussion 'Layout/Project set up Table'
"I used the Kreg Clamp Track and clamp blocks with Rockler T-track to use their inline clamps so I can use it to make boxes. 2nd bench will be drilled with 3/4 holes at 96mm centres with a downdraft box. I have a panel clamp system that will work…"
May 13
Brad Martin replied to Todd J Michalec12@gmail.com's discussion 'Layout/Project set up Table'
"Easier to buy but where is the challenge in that?"
May 11
Brad Martin replied to Lynn Greff's discussion 'What hinge should I use?'
"I would use 3 concealed hinges each side, exact type depends if your doors are flush with the outside edge or set into the cabinet?"
Apr 21
Brad Martin replied to Ken Kortch's discussion 'Cabinet Hardware Jig - Brad Point Bit vs. Regular Twist Bit'
"Brad point is my choice. Lately I have used a plastic cutting board, no splinters from that and it is easy to replace from the local $2 shop. I would align the end with the rail and centred on the rail your drilling."
Apr 21
Brad Martin replied to Larry Prentice's discussion 'Kreg Corner Clamps?'
"I like the look of the new version better, play the waiting game for Caratec to get them in."
Mar 30
Brad Martin replied to Peter DeGregorio's discussion 'Kreg clamp table - Automaxx screw loosens and clamp wobbles'
"If you don't like Loctite then either changing to a bolt or t-bolt would let you spin the clamp in place to retighten it, you may have to do some grinding to get them to slide and you do defeat the free 360 deg rotation."
Mar 24
Brad Martin replied to Bruno's discussion 'Bench dog holes'
"3/4 or 19mm is the Kreg standard hole size. Festool is 20mm as are most dogs from metric countries. Kreg mobile work centre spacing is 4" I belive and Festool use 96mm with Kreg shelf pin Jig and Bosch guide rail at 32mm can do spaces at 64…"
Mar 24
Brad Martin replied to Larry Prentice's discussion 'Kreg Corner Clamps?'
"I was tempted to spend the AU$60 each to get the two that were at Carbatec Adelaide. I like that there is a cut out that lets you make a t-joint as well. What put me off is that they are ugly looking things. I have clamp track and blocks set up…"
Mar 1
Brad Martin replied to Duane Heda's discussion 'Drawer Slide Jig- is it worth the money?'
"On the Kreg I like that you can reverse the jig to fit the drawers as well, it lacks the repeatability of the Rockler with the adjustable height bar. Rockler you have the bar to adjust height but you have to take the slide apart and you can adjust…"
Jan 29
Brad Martin replied to Laura's discussion 'Euro hinges jig question'
"Is this the jig? https://youtu.be/WAHFxRhWB6c Depends on your cordless drill, I know mine would work. The guide traveller would fit your track that I have. Guide Traveller With a bit of work you could make the hole system work too and with any…"
Jan 5

Profile Information

Which Kreg products do you own?
Micro Drill Guide, Deck Jig, Foreman, Kreg Screws, Precision Router Table, Precision Miter Gauge
How would you describe yourself?
Advanced DIYer
How did you learn about the Kreg Owners' Community?
kregtool.com
What's one interesting fact about you, your life, your garage, shop, or home?
I have a 240v Foreman...

Comment Wall

You need to be a member of Kreg Owners' Community to add comments!

Join Kreg Owners' Community

  • No comments yet!
 
 
 

Need Help?

For Technical Support, call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 

Videos

  • Add Videos
  • View All

Forum

Rip-Cut Ruler 4 Replies

Started by Cynthia Alaniz in Beginners' Zone. Last reply by KregCS yesterday.

Concealed hinge jig 1 Reply

Started by Michael B in Kreg Jig® Operation. Last reply by Edward Weitsman yesterday.

Pocket screws to attach table tops 1 Reply

Started by Joe L in General Woodworking. Last reply by Glen S Sep 4.

new member

Started by Al Baker in Beginners' Zone Aug 30.

45 degree angles 1 Reply

Started by Ada Berry in Beginners' Zone. Last reply by Brad Martin Sep 2.

Product Reviews

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 4 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am

© 2018   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_