Kreg Owners' Community

$249.00 portable table saw that has accuracy and precision right down to .0001in. It's here

The table saw is the most used tool you're going have in your arsenal, but lets face it, good table saws are super expensive and big and heavy and even at best the fence is still well... sub-standard on most of them, forcing yet another expensive purchase to get the accuracy and precision you want and expect from a table saw fence.

 

So are there any other options for someone that has a small workshop or a small budget? Is the $5000 dream saw out of reach?  Well there's something here that might tickle your fancy or just make you say ya right or make you go duh!! 

 

The table Saw here is the Ridgid TS4516 10" portable contractor's saw you can find at Home Depot on sale for a whooping $249.00. Hey!! even the 36T rip blade that comes with it is fairly good, but these portable table saws have their limits and it's the power of motor and the size of the table, but for most smaller projects it's more than adequate.

 

Ok.  On to the good stuff...

 

I started off by squaring up the blade like it suggests in the manual.  It was an easy task with the adjustments on the rear of the chassis.  After that I checked the arbor runout with dial indicator.  Great news, it hardly moved the needle as I turned the arbor full rotatations.  This shows that Ridgid put some quality into the design.  With this out of the way, it was time to give this little saw a home inside of a 36 X 24 X 3/4 euro cabinet I found at the local Ikea scratch and dent section for a meager $29.  I added wheels and levelers and a 60 X 30 X 1 1/8" high pressure melamine top I cut to fit around the saw table. I fastened down the top using the K4 pocket hole jig, of course, making this top rock solid to the cabinet.  Plus, for good measure, I added extra pocket holes and screws at the base making it even stronger.

 

The Ridgid 36T blade was replaced with the Freud Thin Kerf 60T Ultra fine finish crosscut blade, (NOTE: I recommend the use of 3 1/2 blade stiffeners with a kerf under 1/8 to minimize blade flutter and vibration and of course, blade noise.) Yes, they're worth every penny if you really care about precision like I do.

 

So what makes this saw so accurate down to .0001?  It's the Incra 25" LS Positioner and fence I adapted from my Incra router table system.  I just wanted to see if this would work as good as it does on my router table. Oh hell ya!!  Even at a full 25" cross cut it's spot on everytime! No matter where you set it.  It's very easy to square up to the blade.  Just pull the fence to the blade and pull the LS Positioner clamp up half way and use the micro adjuster to dial it in perfect and then lock the LS Positioner clamp all the way and run a test cut.  Measure your cut with a digital caliper because this will help you fine tune the fence to perfection.  Once you find the sweet spot, slide the magnetic rule strip on the positioner's carriage to read 0 on the curser line in the window on the LS base and forget about ever using a tape measure again.  "The measure tap cut and scrap method" that is so frustrating will never plague you again!  DO I HAVE YOUR ATTENTION YET?  OK, SO WHAT WILL THIS COST YOU? 

 

The Incra LS 25" will run you about $299 for the package or you can buy the LS Positioner on it's own for $200 and add your own fence, or you can get their fence systems for most table saws made today. (more info at www.incra.com. They also have some cool live demos.)

 

So there you have it!  The little Ridgid saw that has machine shop quality cuts you only dream about for the cost of $750 including the blade, (PLEASE NOTE: I did not in any way modify or re-engineer the table saw itself and I don't recommend doing so for safety reasons. I just made it work better.)

 

Here are some pictures of this setup.  By the way, I decided this setup deserves a nice set of birch cabinet doors for the storage area below. I will post the pictures when they're done. 

 

Also, my sweetheart gave me the Incra Miter 1000SE for Christmas.  These are just must have items for any table saw.

 

Cheers

Glen

Views: 23394

Reply to This

Replies to This Discussion

That looks like a healthy set up there. I have been scouting around for the incra system I will someday own it when I find a great price.

 

Incredibly nice setup. I'm certain it's very accurate, but I'm struggling with the statement that it's "accurate to .0001". I don't see any scales in the photos finer than 1/32". Is there something not illustrated in the photos? Did you mean it repeats to .0001? That is easily believable for a well-built piece of equipment.

An example would be that you set up to cut boards at 10" and all seven boards you cut measured 10.0000-10.0001". Your equipment repeats to .0001". If I asked you to cut a board to 7.3582"+/-.00005, which is .0001 accuracy, and assuming your equipment was accurately zeroed, could you make that setup with your equipment and know you hit that dimension on the first attempt?

If that statement is indeed correct, I humbly offer my apology in advance. :)

The microadjuster moves the fence in precise .001” increments for repeatable accuracy yes, the cut I made was to show how accurate the fence is from one end of the cut to the other end. If I set my cut for 4" on the scale it will read 4.0000 +/-.0001 on the caliper everytime, sorry my bad on the confusion.

 

Cheers

Glen

The micro adjuster will let you adjust in .001" increments so you can sneak up on the right dimension. In woodworking the nature of the material would prohibit accuracy to .0001 temperature and humidity and the fact that wood can be compressed would limit this kind of tolerances.
 I can agree with Glen on the accuracy & precision of the Ridgid Line of tools!

I have their full size contractor saw TS3650, 10” compound miter saw, & a 6” jointer.

They all cut very accurate & perform really well!

 

 For my miter saw I also have Kreg's Precision Track & Stop System which greatly improves it's accuracy & repeatably.

Hi Glen - Good job and a great write up.
Really appreciate the pics.. Making me start thinking about my 4510. I think they are the same saw except for the stand. I know mine was pretty darn good out of the box but it looks like you have added another dimension on a shoestring budget.. Congrats

Thanks John

The accuracy & precision still baffles me. I would have never thought I could nail cuts like this without spending  piles of money. 

Cabinet doors now installed.

 

    

 

 

 

This miter sled adds up to 24" of cross cut capacity in this case 20" with the blade height setup for 3/4 stock with a zero clearance sub-fence added. just thought I would share this

Glen i see you have an incra sled how do you like it? I begining to beleive you incra is the answer to accuarcy in the shop. I am waiting for my incra 1000HD TO COME SHIPPING NEXT WEEK.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_