Kreg Owners' Community

Jens Jensen's Discussions (776)

Discussions Replied To (729) Replies Latest Activity

"nothing fancy but convertible https://kregjig.ning.com/photo/im003919-1?context=album…"

Jens Jensen replied Feb 17, 2013 to A little help.

5 Feb 17, 2013
Reply by Bob DeMay

"I have blown air into all tools to clean up after every usage but now instead of blo…"

Jens Jensen replied Feb 16, 2013 to Ready to purchase a Router

23 Feb 17, 2013
Reply by Ken Darga

"I also saw them off but I use a worn out orbital sanding disk and place over the plug"

Jens Jensen replied Feb 12, 2013 to Plug Trimming

2 Feb 12, 2013
Reply by Jens Jensen

"You might consider the following link and look into there refurbished tools .Warrant…"

Jens Jensen replied Feb 12, 2013 to Ready to purchase a Router

23 Feb 17, 2013
Reply by Ken Darga

"George read this link your question will be answeredhttp://www.minwax.com/wood-produ…"

Jens Jensen replied Jan 31, 2013 to Using pre-stain liquid

4 Jan 31, 2013
Reply by Ken Darga

"I have done a couple and what I would suggest is add a desk on back side of drawers…"

Jens Jensen replied Jan 30, 2013 to Loft Bed plan

9 Apr 5, 2013
Reply by Eric Miller

"Thanks Yes I no ours did not have em"

Jens Jensen replied Jan 22, 2013 to table vs radial saw

20 Jan 22, 2013
Reply by Jason Watkins

"Jason my saw has been in family since day itws delivered to my dad and I never recal…"

Jens Jensen replied Jan 22, 2013 to table vs radial saw

20 Jan 22, 2013
Reply by Jason Watkins

"Couple more shots one is my edge sander which is a 70's model "

Jens Jensen replied Jan 21, 2013 to table vs radial saw

20 Jan 22, 2013
Reply by Jason Watkins

"Being 135.00 is quite a chunk of change I spent 1.50, and got same resuts took the s…"

Jens Jensen replied Jan 21, 2013 to table vs radial saw

20 Jan 22, 2013
Reply by Jason Watkins

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Accu-Cut XL track alignment issue 1 Reply

Hi All,I'm just wondering if anyone else has had this issue and can help me,I recently purchased the Accu-Cut XL and when I went to put the track together I noticed that one of the tracks was different to the others The alignment of the track guide…Continue

Started by Al Barale in Community-Specific. Last reply by KregRep on Tuesday.

Advice on assembling the "offset" bottom of a wall cabinet

Hi,I'm about to build my first wall cabinet, using 3/4 plywood for the box and 1x2s for the face frame. Everything will be assembled using pocket hole joinery. I've attached a basic image of what the cabinet box will look like.I'm planning to have…Continue

Tags: cabinet, holes, pocket

Started by Jeff Welsh in Beginners' Zone May 26.

Product Reviews

Kreg Jig Dust Collection Attachment

1st impression when you hold this attachment in your hand:  "not much to it", Kreg sure is makin' $$ here.



Then I installed it.. perfect fit, leaves just enough room to adjust the setting screw on my K4.



Then the real test, hook…

Continue

Posted by Grampy Meyer on February 23, 2020 at 11:36am

My K4 Master System

I picked up the K4MS from Home Depot about 3 months ago, I was looking for a small filing cabinet for under my desk and nothing I looked at would fit or they wanted big money for it, my wife said “why don’t you just build your own then you will…

Continue

Posted by Randy W. Lush on August 25, 2019 at 12:30pm

© 2020   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_