Kreg Owners' Community

I am making some oak furniture and on some sides the pocket holes will be visible.  I don't really mind this at all because I want to use a contrasting wood for my pocket hole plugs.  I think I saw this on the beginner video.  I want to stain the oak a darker color and have a lighter wood in the plugs.  My question is how can I put a lighter wood in the hole and not get stain on it.  My thoughts are that if I put the plugs in and stain the wood, the lighter wood will also get the stain.  If I put the plugs in after I stain, I would have to sand the plug smooth which would take off my stain correct?  So what is the proper way to do this.  Thanks to all.

Views: 712

Reply to This

Replies to This Discussion

I haven't tried that but it's an interesting idea. Maybe, don't glue the plugs in right away. Sand them smooth, remove the plugs, stain, then glue the plugs in. That would mean you would probably need a way to keep the plugs organized so they all go back into the correct hole. Just a random thought from a wandering mind :-)

Andrew, 

To accomplish the desired effect,

I'd stain the pieces first, then install the plugs.

1. stain your desired pieces.

2. install the unfinished plugs.

3. cut the plugs flush, using a small ''flexible flush trim saw''.

NOTE:  the flush trim cutting teeth on this type saw, have no saw-tooth set, the teeth are flush with the saw blade thickness, and will not scratch the finished surface.

4. ''if necessary''--- sand the plug ends, using a short section of 1/4" dia dowel rod---

glue a 120-150 grit piece of sandpaper to the end of the short dowel rod---

cut the sand paper, flush with the OD of the dowel rod---

the result should be that the sand paper will be affixed to the end of the dowel rod, and not extending out from the edge of the dowel rod.

5. while sanding the plug ends, using a slow back-and-forth motion or a rotating motion; akin to using a pencil eraser---

this can be accomplished by hand or chuck the short piece of dowel rod in a slow rotating drill.

 

ALTERNATE METHOD:  A small screw can be placed in the end of this short dowel rod---opposite the end with the sandpaper.

Remove/cut off the head of the screw---chuck this short dowel rod, with the screw fitted into an adjustable chuck of a dremel tool.  The right angle accessory, for the dremel is especially handy for this task.

 

Apply ''light'', soft touch, sanding pressure to the end of the plugs, to obtain the desired smooth finish.

 

6.  Stain the ends of the plugs, to the desired colored, using a small artist brush.

 

WORKS FOR ME. 

 

PS---

ALTERNATE method:

A short piece of dowel rod, can be affixed in a hex-nut driver---secured in place using hot-melt glue---secure the short piece of dowel rod into the nut driver.

Using the nut driver in a rotating motion, to accomplish the rotating sanding task, to the plug ends, to make smooth.

 

TIP:  applying masking tape, to the adjacent finished area, so as to prevent scratch/sanding marks.

Apply the tape over the plug---cut the tape away, over the ends of the plugs, using an exacto pointed blade knife tool.

 

I haven't tried this but after gluing and staining the plugs, you could seal them with CA (super) glue before staining the oak. I would test this first because not all super glues are the same.

 

Instead of using oak plugs why not try using plugs made of maple or even the paint grade plugs

 

i agree with ray, though i've never tried, it might be worth it to purchase a few different types of kreg plugs, sand them individually and test your final stain on them. i would think different woods would take on different shades. a few of the oak plugs i used on oak wound up looking lighter or darker because the grain didn't quite match up (something i hadn't thought of when i plugged them.) 
On lighter color woods I use rosewood dowels. On dark wood use pine or birch.
use the maple plug,  stain the project without plugs,  add plugs and as ken said use the jap flush cut saw to cut the plugs, restain to hit with same stain and wipe it quickly,, maple is alot more dense than oak,, less poreis so you should keep a lighter color on the plugs.  good luck
Also u could drill a pocket in scrap wood put dowell in cut and sand it .Poke it out from back and go to next one until all are cut then after that stain is dried put  plugs in and its a done dea.I have a VIDEO ON YOUR SITUATIONl
Could you send me a link to your video?  This sounds interesting.  Thank you!

Jens Jensen said:
Also u could drill a pocket in scrap wood put dowell in cut and sand it .Poke it out from back and go to next one until all are cut then after that stain is dried put  plugs in and its a done dea.I have a VIDEO ON YOUR SITUATIONl

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_