February 2015 Product Reviews (3)
Radial Arm Drill RAD
I bought this Drill in the last quarter 2014.
Its not your average Drill Press so I thought I would post a review for it.
My Radial Arm Drill review RDP-116
Type
Carba-Tec branded 5 Speed Radial Arm Drill Press.
Motor is ½ hp
5 speed pulley system 500 to 2450 RPM
Keyed Chuck capacity 1 to…
ContinueAdded by Robert Brennan on February 28, 2015 at 3:00pm — 2 Comments
Square Cut
just bought one, great idea! i like to use my ryobi 18v 5 1/2 circular saw alot. i found that the square cut guide arm does not reach the saw base. i was wondering if it would be ok to drill another hole to fix this? their are other circle from the manufacturing process that i think i can use as a guide. whatcha think??
rob
Added by Rob Davenport on February 21, 2015 at 6:29pm — 2 Comments
Foreman DB210
Added by Lanelle Warrick on February 13, 2015 at 1:34am — 1 Comment
Latest Product Reviews
Most Popular Product Reviews
Monthly Archives
2020
2019
2018
2017
2016
2015
- December (1)
- November (1)
- October (1)
- September (3)
- August (1)
- July (1)
- May (2)
- April (1)
- March (2)
- February (3)
- January (1)
2014
- December (1)
- November (1)
- September (2)
- August (2)
- July (3)
- June (3)
- May (3)
- April (1)
- March (2)
- February (2)
- January (4)
2013
2012
- December (1)
- November (2)
- October (2)
- September (1)
- August (3)
- July (8)
- June (1)
- May (4)
- April (3)
- March (1)
- February (1)
2011
2010
- December (1)
- November (7)
- September (1)
- August (4)
- July (1)
- June (4)
- May (14)
- April (73)
- March (16)
- February (18)
- January (27)
2009
Need Help?
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
Popular Posts & Projects
Videos
Forum
Concealed Hinge Jig Setting Confusion
The Kreg Concealed Hinge Jig has a setting for the distance from edge of the door to the nearest edge of the 35 mm cup hole. This can be set as 3, 4, 5, or 6 mm.Later in the instruction there is a table that converts the distance from the edge of…Continue
Started by Ken Kortch in Kreg Jig® Operation Oct 11.
Help with old Rip-Cut(tm)
I have an old Rip-Cut which I bought many years ago but did not set. I seem to have lost the instructions, if I ever had them.I cannot figure out which bolts are match with the nylon-lock screws.This unit is old enough that the current instructions…Continue
Started by Sean in Other Kreg® Products Oct 4.
Product Reviews
Not Pleased With Pocket Hole Construction
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 1 Comment
Kreg Jig Dust Collection Attachment
1st impression when you hold this attachment in your hand: "not much to it", Kreg sure is makin' $$ here.
Then I installed it.. perfect fit, leaves just enough room to adjust the setting screw on my K4.
Then the real test, hook…
Posted by Grampy Meyer on February 23, 2020 at 11:36am
© 2020 Created by KregRep.
Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service
