Kreg Owners' Community

January 2013 Product Reviews (5)

Kreg Universal Drawer Slide Mounting Jig & Brackets Review

One of my favorite toys is my Kreg Drawer Slide Jig.  There are actually two jigs that you'll want to use to help you install a drawer.  These two jigs really compliment each other, and make completing drawer installs a snap.  I picked up both jigs from Amazon for a really reasonable…

Continue

Added by Daris R. on January 30, 2013 at 12:30am — 4 Comments

Kreg Rip Cut

I was fortunate enough to receive a Kreg Rip Cut last spring as they were first shipping but didn't begin using it until this fall.  Initially I attempted to attach the Rip Cut to my Worm Drive Mag framing saw.  The base of that saw has a lip that is great for pushing dust out of the way but makes it difficult to attach the Rip Cut, so I got out my back up saw- an older…

Continue

Added by Kevin Bergstrom on January 29, 2013 at 5:30pm — 12 Comments

Kreg sawdust jig relief

We have found the holes in the three hole block imeed the discharge of sawdust during the final depth of the drill bit. We do a lot of hard wood work which appears to be when this plugging of the discharge holes occures. We were wondering if anyone else has this problem and if a solution would be to lower the relief holes to allow sawdust discharge nearer the base of the block.

Added by James Lindemulder on January 25, 2013 at 12:33pm — 5 Comments

My new Kreg tool box

I received a Kreg tool box for Christmas this year.  I love it.  I now have a place to keep all of my Kreg clamps, extra drill bits, extra driver bits, and even my Kreg tool in the bottom of the tool box.  I love the removable trays for screw in the top of the box and the see thru lid.  I love the way that the top is supported with the legs in the back when you lift the top lid to get to the bottom.  The only way this box could have been better is is the bottom was a little deeper but it's…

Continue

Added by David Niebeling on January 12, 2013 at 7:06pm — 5 Comments

Square Cut is not square

I bought a Square Cut to use with my circular saw.



Just before making the first cut I decided to check the angle, and unfortunately the “right angle” came out not to be exact. At first I became very frustrated and was ready to throw it away on the upper shelve. But, as several cuts had to be made at the time, I solved the problem by sticking several pieces of…

Continue

Added by Misha on January 11, 2013 at 1:13pm — 10 Comments

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_