Kreg Owners' Community

When it comes to using something to help with keeping cross cuts and rips straight, what do you prefer to use and why?  



Peach Tree

Or a homemade plywood/straightedge jig

This is assuming you would be using a circular saw or jig saw and do not own a table saw.

Views: 1417

Reply to This

Replies to This Discussion

Hi Keith, I use the tru grip clamp & tool guide, I have two 50 inch guides and a 8 foot guide. They work great,easy to use and hold pretty good. I use them for both my saws and as a router guide,both are used at the America time for the routers.

thanks, Rich!  I'll have to look into those.

Rich, is that the one by Griset?

If you don't mind spending the money, I've recently upgraded to the festool TS 55 plunge saw with track system. Well worth it, easy to use, accurate and the cuts are clean & smooth, finish ready.I cut all my sheet goods down with that now.
Yes ,griset industries

I have used the Kreg rip cut many times successfully.   I also made my own straight edge jig of a 4ft length.  I placed wall board and slat board on my garage walls a couple of years ago and cutting down 4x8 sheets was a challenge for me made easier using those two methods.

I just routed in tracks to my work bench in progress yesterday with the Rockler Low profile straight edge system.  It was easy to use and the T-Square feature kept me in check.  

Keith, you can have the best guide but still get mediocre cuts from a circ saw -- I do it all the time. That's the main difference between a quality track saw and my Makita contractor grade circular saw. Accurately aligning the base to the blade is well nigh impossible. Unless the saw blade can remain parallel and perpendicular to the edge of the saw base, the best guide does little to help.


I purchased two different higher priced circular hand saws---

neither one had the blade aligned with the base.

One saw had a variation of  .04 to .06", from the front of the blade to the back of the blade, and the other was .03 to .04", in a span of just 7".  (The blade was not parallel to the base).

It's acceptable for cutting 2X lumber free-hand; however, 

unacceptable for making accurate cuts with a straight edge guide.

I took one saw to the OEM's authorized servicer---they couldn't do anything with it.

Changing out the base plate, still produced the same results.

Both brand saws are currently made in China.

Returned both of them to the dealer.

Went back to using my older reliable saw, which makes accurate straight cuts, 8 ft long and within .02-.03,

using a straight-edge guide.

Jay Bates has a  slick setup with dust collection.

Ken, you highlight the glaring differences between contractor grade and cabinet grade tools. The walls of my house are plumb to 1/4th inch, while my built-ins are to 1/32nd.
There's a reason why Festool costs so much! It's called accuracy, precision, and repeat ability.


The saws, described above, did not have the "pivots" or the "mounting" feature in alignment with the base plate, thus the reason the blade and base were not in aligned.

I surmise its a manufacturing machining issue.

Reply to Discussion


Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Popular Posts & Projects 


  • Add Videos
  • View All


Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…


Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…


Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service