Kreg Owners' Community

rich b.'s Discussions (15)

Discussions Replied To (14) Replies Latest Activity

"Jay is 100 percent right,I use plywood on a lot of projects and custermers are infor…"

rich b. replied Jul 30, 2014 to Misrepresentation and Trust

8 Jul 30, 2014
Reply by Gary roofner

"Hi Jody. I would think ,without seeing the layout for joining everything, the 2 1/2…"

rich b. replied Jun 8, 2014 to Need advice please !

2 Jun 8, 2014
Reply by Paul Crow

"Hi Keith. I buy it by the gallon then spray it on ,several coats and sand very light…"

rich b. replied May 18, 2014 to Staining Pine Question; need some assistance

10 May 19, 2014
Reply by thomas b farrell

"Hi Keith. Justin and Rita are right,I have been spraying and brushing stain on ,I pr…"

rich b. replied May 18, 2014 to Staining Pine Question; need some assistance

10 May 19, 2014
Reply by thomas b farrell

"Hi Keith. Your best bet is a lumber yard or specialty wood supplier,some older lumbe…"

rich b. replied Apr 28, 2014 to In search of.....true 2x2 lumber - help

10 May 1, 2014
Reply by Gary roofner

"Hi Steve, if you use good quality plywood and it is sealed on both sides it should l…"

rich b. replied Apr 28, 2014 to Plywood life expectancy ?

3 Apr 29, 2014
Reply by Jay Boutwell

"Hey woody,if your drilling through the 2x4. Into 3/4 stock the set up should be pret…"

rich b. replied Mar 30, 2014 to setting up

4 Apr 1, 2014
Reply by KregRep

"If you start doing more you can shop around,see what you save buying in bulk,as a bu…"

rich b. replied Mar 28, 2014 to Picture Frames For Profit?

6 Apr 1, 2014
Reply by Rick

"Bryan is right,it's a fine line , what is too much or not enough.The time is yours b…"

rich b. replied Mar 26, 2014 to Picture Frames For Profit?

6 Apr 1, 2014
Reply by Rick

"Ken is right, I also have both a cabinet saw and a 745 ,and I have had both of them…"

rich b. replied Mar 23, 2014 to Can One Live Without a Table Saw?

34 Mar 23, 2014
Reply by rich b.

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Concealed Hinge Jig Setting Confusion

The Kreg Concealed Hinge Jig has a setting for the distance from edge of the door to the nearest edge of the 35 mm cup hole. This can be set as 3, 4, 5, or 6 mm.Later in the instruction there is a table that converts the distance from the edge of…Continue

Started by Ken Kortch in Kreg Jig® Operation Oct 11.

Help with old Rip-Cut(tm)

I have an old Rip-Cut which I bought many years ago but did not set.  I seem to have lost the instructions, if I ever had them.I cannot figure out which bolts are match with the nylon-lock screws.This unit is old enough that the current instructions…Continue

Started by Sean in Other Kreg® Products Oct 4.

Product Reviews

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 1 Comment

Kreg Jig Dust Collection Attachment

1st impression when you hold this attachment in your hand:  "not much to it", Kreg sure is makin' $$ here.



Then I installed it.. perfect fit, leaves just enough room to adjust the setting screw on my K4.



Then the real test, hook…

Continue

Posted by Grampy Meyer on February 23, 2020 at 11:36am

© 2020   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_