Kreg Owners' Community

Ken Kortch's Discussions (87)

Discussions Replied To (75) Replies Latest Activity

"There are really only three "settings" associated with a Kreg Jig: 1. Distance from…"

Ken Kortch replied Sep 14, 2019 to Hard time pocketing 2x4

3 Oct 8, 2019
Reply by Ken Darga

"I don't use a K5 jig so excuse my ignorance. Can't you just set the jig height for…"

Ken Kortch replied Apr 15, 2019 to Back with Kreg

3 Apr 17, 2019
Reply by KregCS

"The best router bit advice I've read is to invest in a decent lower cost router bit…"

Ken Kortch replied Jan 12, 2019 to Router bits

5 Feb 15, 2019
Reply by brinda Ashley

"If you were using a 2x6 instead of the 1x6 I might suggest using the Kreg HD Jig wit…"

Ken Kortch replied Sep 28, 2018 to 1x6 into a 4x4?

4 Sep 29, 2018
Reply by Edward Weitsman

"I assume that the pocket holes will be in the 1x6, and the sharp end of the screw wi…"

Ken Kortch replied Sep 25, 2018 to 1x6 into a 4x4?

4 Sep 29, 2018
Reply by Edward Weitsman

"Honestly, though I don't own an R3 (I own the K4 Master system) I think you can do a…"

Ken Kortch replied Aug 16, 2018 to Just wondering

4 Aug 30, 2018
Reply by Al Baker

"It seems that most people seem to use SketchUp, which is available at no cost for no…"

Ken Kortch replied Apr 15, 2018 to designing your projects online

4 Apr 19, 2018
Reply by KregRep

"Using simple linear regression (fitting a line of best fit through points on a graph…"

Ken Kortch replied Apr 14, 2018 to Kreg Jig Mini Measurements?

26 Apr 14, 2018
Reply by Ken Kortch

"OR ... the Kreg Custom Pocket-Hole Plug Cutter with the "to-be-purchased separately"…"

Ken Kortch replied Apr 2, 2018 to Plugs For 2x4's

4 Apr 9, 2018
Reply by Glen S

"I brought this up a little bit ago here and didn't get much feedback. I wish it had…"

Ken Kortch replied Mar 13, 2018 to K4 Jig Clamp Screw

4 Mar 15, 2018
Reply by Glen S

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Drawer Slide Jig - How to fit bottom drawer? 2 Replies

Hi guys.I'm probably being really stupid here, but I cant see any way to use the drawer slide jig to fit the bottom drawer of a set?I actually have a couple of questions:Firstly, should the drawer slide fit flush with the bottom of the drawer?(That…Continue

Started by Craig in Beginners' Zone. Last reply by Craig 10 hours ago.

Combination Pocket Hole and Tongue & Groove Joint

All material is 3/4"Tongue & groove is 1/4" tongue into a 1/4" grooveMy thinking is to set the jig and bit as though I was using 1" stock.  Use the screw called out for 3/4" material.  Is my thinking correct.ThanksGeorgeContinue

Started by George in Beginners' Zone Jun 13.

Product Reviews

Kreg Jig Dust Collection Attachment

1st impression when you hold this attachment in your hand:  "not much to it", Kreg sure is makin' $$ here.



Then I installed it.. perfect fit, leaves just enough room to adjust the setting screw on my K4.



Then the real test, hook…

Continue

Posted by Grampy Meyer on February 23, 2020 at 11:36am

My K4 Master System

I picked up the K4MS from Home Depot about 3 months ago, I was looking for a small filing cabinet for under my desk and nothing I looked at would fit or they wanted big money for it, my wife said “why don’t you just build your own then you will…

Continue

Posted by Randy W. Lush on August 25, 2019 at 12:30pm

© 2020   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_