Kreg Owners' Community

Hi All...

I purchased the Kreg Jig Mini today, planning on joining some 1" (actual thickness) hardwood stock. Is there a chart that lists jig position and depth collar information for stock with an actual thickness other than 3/4", 1/2", and 1 1/2"?.

I've spent the last hour scouring Google and these forums, and cannot for the life of me find any information about this. Without this simple information the jig is basically useless to me :(

I would drill some test holes to try and figure it out, but I'm making a table out of an old door and therefore don't have any extra wood to use for testing...

Thanks for any help you can provide!

-Dan Coes-

Views: 19591

Reply to This

Replies to This Discussion

John,

Sorry for posting to this old thread but like others I too having purchased the Kreg mini-jig and set out to solve this trig problem.  I was in process of doing a search to see if jig dimensions (those that you provided as “z” - 70 mm and “x” – 35.45 mm) were public knowledge anywhere to ensure my calculations were correct when I came across your post.  I believe there is an error in your sketch however in that you should reverse positions of “w” and “≈x” where they appear along the drill bit centerline such that the sketch will align with the assumption you stated as:

  • that the depth of wood left from the bottom of the pocket to the timber face is equal to the thickness of the timber

The way you have it sketched is showing the depth of wood removed as equal to thickness of lumber when in fact the “face” being referred to in the assumption is the face of the joint and not the face where the bit first enters the wood.  Reversing positions of these two variables makes sense because it is the wood that remains (not wood removed) that resist tear out of the joint.  It is also why the problem is not as simple as adding 70mm to the thickness of wood being used as one reader suggested (although that reason would align with the drawing provided).  In fact ≈x must be calculated as I supsect you have done.

The other assumption needed to solve this problem with certainty (which you show in your sketch and use in the equations but did not explicitly state) is:

  • “the longitudinal axis of the screw should pass through the midpoint of the drilled wood’s thickness”

Starting with dimensions you provided together with both assumptions it’s easy to visualize that Y is defined by the position necessary to make the centerline of the bit pass through the midpoint of thickness (using mm for constant and degrees for the angle*):

  • Y= ((1/2W) / Tan(15)) – 35.45 mm
  • * noting that Excel trig functions require conversion to radians in place of angles

then, having defined Y, solve for “≈x” necessary to add to 70 mm such that it leaves “w” length of wood to resist tear out (again using mm for the constant and degrees for the angle)

  •  ≈x = ((x + y) / Cos(15)) – w
  • Collar offset = ≈x + 70 mm

Finally these calculated values give the ideal dimensions for setting the stop collar and jig offset which will be rounded (down for ≈x  and up for Y to avoid screw protruding through second workpiece) to the nearest measuring tape increment.  Then screw choice would be the longest standard screw available that does not exceed 2 times “w”.

I’ve restated equations above since I come up with slightly different values than your original spreadsheet.  I wasn’t sure if those differences though were attributable to equation differences or simply due to rounding choices (metric vs. imperial or decimal vs. measuring increments) and hence the request that you confirm the above is what your spreadsheet uses or repost a new version of your very well formatted spreadsheet as may be appropriate.  I'll attach my more rudimentary spreadsheet in case it makes that easier to do.

KregMini_Joe.xlsx



John James said:

Hi Peter again,

Having cracked my spreadsheet passwords, you're quite right; I had mis-typed the two formulae noted on the spreadsheet, though the actual calculation was right*.  I've updated the spreadsheet, and uploaded the revised version together with the diagram, with this reply.

*  it still gives -11mm - rather than Kreg's own figure of -6mm - for 13mm or ½inch timber.

Using simple linear regression (fitting a line of best fit through points on a graph):

Thickness = Material Thickness


Distance_from_Edge = -1.076923077 + (1.538461538 x Thickness)

Drill_Collar_Depth = 2.814903846 + (0.951923077 x Thickness)

Screw_Length = 0.826923077 + (0.461538462 x Thickness)

A negative Distance_from_Edge means that the jig is hanging over the material.


Actual:

Thkns, Edge, Colr, Scrw

0.5, -0.25, 3.3125, 1

0.75, 0, 3.5, 1.25,

1.5, 1.25, 4.25, 1.5

Estimated:

Thkns, Edge, Colr, Scrw,

0.5, -0.31, 3.29, 1.06

0.75, 0.08, 3.53, 1.17

1.5, 1.23, 4.24, 1.52

Not too bad. I hope this helps you until/if Kreg can give better information.

Ken

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_