Kreg Owners' Community

E M Hampton
  • Edmond, OK
  • United States
Share on Facebook
Share

E M Hampton's Discussions

Driver Bit Issue
8 Replies

Hello All. First of all, I am very pleased with all my Kreg equipment...except for one tiny annoyance. Does anyone else have problems with the square heads of the driver bits rounding off and (then…Continue

Started this discussion. Last reply by Glen S Jun 20.

 

E M Hampton's Page

Latest Activity

Glen S replied to E M Hampton's discussion 'Driver Bit Issue'
"The screw wax made driving the screws a whole lot easier!"
Jun 20
Glen S replied to E M Hampton's discussion 'Driver Bit Issue'
"You're Welcome. I hope that trick works for you. I also bought some screw wax that I'm going to try on a Tiger Maple face frame."
Jun 14
E M Hampton replied to E M Hampton's discussion 'Driver Bit Issue'
"Thanks, Glen. Will pick some up and try them. Thanks for the drill position tip. Will try it next time I am using the jig. "
Jun 14
E M Hampton replied to E M Hampton's discussion 'Driver Bit Issue'
"Thanks, KregCS. I do try to let the screw do the work. Since you can't see the screw head and you driving at an angle, it is a bit more of a challenge to align properly. Will try harder, but will also get hardened tips. I am sure I'll…"
Jun 14
Glen S replied to E M Hampton's discussion 'Driver Bit Issue'
"Mine stripped quickly too. I bought Hitachi bits from Menards & never looked back. Also rather than holding the drill like you normally would with the handle to the left or right. Turn the drill upside down,, cord or battery straight up. Just…"
Jun 7
KregCS replied to E M Hampton's discussion 'Driver Bit Issue'
"Mr. Hampton,  When driving in your screws you will want to make sure that the driver is fully engaged with the screw head.  Due to the angle the screw is being driven in at, if this is not fully engaged it will greatly increase your…"
Jun 6
E M Hampton replied to E M Hampton's discussion 'Driver Bit Issue'
"Thanks, Tim. The only ones I see at Rockler, however, are labelled: Kreg Jig® HD Driver Item #: 47983. Are they the ones you ordered?"
Jun 4
Tim Grace replied to E M Hampton's discussion 'Driver Bit Issue'
"Mine rounded off quite quickly, as well.  I attributed it to using an impact driver to drive the screws, some of which had space restrictions and required awkward angles.  I did pick up a couple at Rockler that had hardened tips and lasted…"
Jun 3
E M Hampton posted a discussion

Driver Bit Issue

Hello All. First of all, I am very pleased with all my Kreg equipment...except for one tiny annoyance. Does anyone else have problems with the square heads of the driver bits rounding off and (then of course) stripping out? I suspect technique may be contributing, but I also wish they were perhaps a bit deeper and harder. Anyone else have this problem or abe to offer any suggestions? Thanks in advance. See More
Jun 2
E M Hampton replied to KregRep's discussion 'New Members: Please introduce yourself.'
"Hello. Monty here from Oklahoma. Long time (self-proclaimed) DIYer, but previously more concerned with function over form (admittedly, it showed). Recently retired at 60 and am looking forward to upgrading all my older, contractor grade equipment…"
Apr 25, 2016
E M Hampton replied to Patrick Willyard's discussion 'Universal Bench Top'
"Hello - new to the community. Purchased Universal Bench Kit (64 x 28). Intended use - general purpose mobile workstation. Contemplating using 36 inch solid core door with a white faced hardboard as the work surface. A few questions for…"
Apr 25, 2016

Profile Information

Which Kreg products do you own?
Kreg Jig® K4, Shelf Pin Jig, Universal Bench, Kreg® Routing Systems
How would you describe yourself?
Intermediate DIYer
How did you learn about the Kreg Owners' Community?
KregTool.com
What's one interesting fact about you, your life, your garage, shop, or home?
Equipping shop from scratch.

Comment Wall

You need to be a member of Kreg Owners' Community to add comments!

Join Kreg Owners' Community

  • No comments yet!
 
 
 

Need Help?

For Technical Support, call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 

Videos

  • Add Videos
  • View All

Product Reviews

Kreg Mobile Project Center

I just picked up my new Kreg Mobile Project Center Item #KWS1000.

Wow!  I set it up in my basement and it is great addition to my Kreg items.  I was viewing a video where a review on this fine product was being made, which prompts…

Continue

Posted by John Tomkinson on May 5, 2017 at 5:34am — 2 Comments

Handy jig to hold and push plugs in!

Takes 10 minutes to make this handy accessory for your Kreg gear! Home made plug pusher.

Posted by Dave Stanton on March 31, 2017 at 5:53pm — 1 Comment

© 2017   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_