Kreg Owners' Community

Kreg Jig® Operation (272)

Discussions Replies Latest Activity

K5 port

I just got my K5, and it's really nice. However, I cannot find a nozzle to fit the vavuum port, and I can't locate an adapter to make it fi…

Started by Barbara Dyer

8 on Monday
Reply by Scott Russell

Kreg HD Drill Bit Durability

Has anyone snapped the tip of an HD drill bit yet? I noticed one complaint on Amazon. I am curious if there have been more or is this an is…

Started by uglyfatjoe

21 Feb 12
Reply by Dennis Hofer

Suggestion: K4 Drill Guide Pin with Square Drive

I have a K4 Kreg Jig Master System. With the Dust Collection Attachment in place I find it almost impossible to loosen/tighten the brass (?…

Started by Ken Kortch

1 Feb 5
Reply by KregCS

Pocket hole tearout

I was assembling a cabinet today and screwed the screws into the other panel,the did the same thing on the other side and moved it slightly…

Started by daddywoofdawg

2 Jan 22
Reply by Dan Duce

Angles less than 90 degrees - where to drill the pocket hole

Hey all, New to Kreg system, but not new to DIY stuff.  Just bought a K5 system and added an HD jig as well.  I'm attempting to build an aw…

Started by Marcus Waddell

4 Jul 21, 2017
Reply by Marcus Waddell

Pocket holes in beveled edges

I'm in the middle of building a farmhouse table base, and want to add corner braces across the top of the leg to adjacent apron pieces. The…

Started by Keith M.

4 Jul 7, 2017
Reply by Jay Boutwell

Kreg Jig and Screw Length Settings Web App

After about the 20th time searching for the thread and wonderful PDF guide that outlines screw length and jig setting guidelines, I decided…

Started by Mike Retzak

17 Mar 6, 2017
Reply by Michael Mull

Has anybody mounted the Bandsaw fence on a 10" Rockwell?

 I would like to mount the fence on my 10" Rockwell. I know I'm going to have to drill and tap the holes but what's the distance between t…

Started by Bill McMillan

0 Feb 25, 2017

Kitchen Cabinets

I'm using 1/2-inch plywood sides and spacers for new kitchen cabinets but I'm using 3/4-inch plywood for the bottom shelf. I plan to use po…

Started by Jerry Lewis

3 Feb 22, 2017
Reply by Ken Darga

question about kreg foreman and tear out

I believe am getting a lot of tear out on the right side of my pocket holes on 3/4 inch material. Its a new bit as I just got the tool so i…

Started by Michael

2 Dec 31, 2016
Reply by Michael

RSS

Need Help?

For Technical Support, call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 

Videos

  • Add Videos
  • View All

Forum

Pneumatic conversion pocket hole 2 Replies

Started by Michael B in Beginners' Zone. Last reply by KregCS on Monday.

Kreg Storage 2 Replies

Started by Jim Mahan in Kreg Jig® Projects. Last reply by R. E. Woods on Friday.

Old Kreg Jig - K1?

Started by Kent Bruner in Kreg Jig® Purchasing Feb 11.

concealed hinge jig stop collar 1 Reply

Started by Joe Grane in Other Kreg® Products. Last reply by KregRep Feb 12.

Kreg Jig K3 defect or not? 5 Replies

Started by Igor in Kreg Jig® Purchasing. Last reply by Randy Hills Feb 13.

Product Reviews

Kreg Foreman

I have built many kitchens and finally decided to buy the Foreman, because my latest kitchen consisted of 28 cabinets and I was over my hand hurting from all the drilling, moving the clamp etc., it seemed like a smart choice.

The…

Continue

Posted by justin waldron on January 8, 2018 at 4:05am — 2 Comments

Kreg K5 Jig Review

Posted by Daris R. on November 20, 2017 at 5:39pm

© 2018   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_