Kreg Owners' Community

Hi,

Small shop shelf. I got all my pieces cut out, sanded, put in my homemade 90 degree jig. Attached all the shelves to the right side of the storage shelf but when I went to pocket hole the second side on there was no way I could get to the pocket holes with my drill. the shelf is only 9 inches and the Kreg drill bit alone is at least 5 inches. So I ended up counter-sinking and drilling from the outside of the 3/4 inch plywood and naturally the plywood went to H...!

I should have used nails I guess. What do you do when your Kreg Pocket Hole Jig project is to small to get a drill inside of to put in the screws to the second side???

Thanks in advance,

Bill in Las Vegas

Views: 1193

Reply to This

Replies to This Discussion

Take a look at this discussion from a couple of months ago.

http://kregjig.ning.com/forum/topics/unable-to-drive-kreg-screws-in...

Right angle drill attachment.   The one that comes with the Festool CXS is excellent.  

Price: $285.00 SKU: 564535  Brand: Festool
Just a bit more than a pre-beginner can afford. But I did check it out on YouTube and saw it in action.
Thanks again Russ,
Bill in Las Vegas
<>/span>
I went with the $29 Genesis cordless drill so I could afford more Kreg toys. :-)

Plenty of more affordable options for the same task, e.g. $8 from Amazon.  

William,

There are a couple different things you can do for this situation.  One is you can use a socket wrench and the 3" driver.  With this method you will just need to make sure that you follow the correct angle when driving the screw.  The second option would be to use a flex driver.  This allows you to use your current drill but brings it outside the box.  The last option would be to use a 90-degree drill.  This should give you more than enough room in your project.  Hopefully one of these options will work for you.  If you have any questions on these options, please let us know. 

Thanks much for all of your replies.

Bill in Las Vegas

<>/p>

if you have an air compressor, I really like to use my air drill, it is very compact and powerful. You just have to be careful not to strip the hole by over tightening. you can buy this one at Harbor Freight Tools.

hey bill,

sorry to hear you had problems. really, kreg joinery is the bomb when it comes to simple, strong joints. i've had to be pretty creative also, getting into tight spots. usually i use on my right angle drill with a short bit to get into teeny tiny spaces. i didn't exactly need another drill, but ryobi makes really cool green tools ;-)

I ran into this situation this past week-end.  Fortunately, I had the pocket holes drilled prior to the assembly.  Getting into the tight spots to install the screws created the problem.  I have a Craftsman NexTec drill that is fairly small, that allowed me to get to most of them.  I also have a ¼" flex drive that allowed me to get into the tighter ones.  I do have a 90º angle attachment, but didn't want to remove the chuck on one of the drills to install the attachment.  I've also got some small ¼" finger ratchets that allowed me to get to the last couple.

Thanks Tim, all great ideas. I appreciate everyone's help on this. I bought a Genesis cordless drill, but I think my old rachets might have more power. I guess if I'm going to work like the big boys I might have to by some of the big boy tools. <grin>  Bill in Las Vegas

Hey Tim, How did you do the lettering on your jewelry box? Bill in Las Vegas

Quick-Change chuck adaptors, such as shown, or the like, can be inserted into the drill chuck,

for 1/4" hex driver tools/bits, and the like.

Works for me.

3/8' Shaft Adaptor (left) allows you to pop your pocket hole drill bit into the Quick Change Chuck (right). I found this at Rocklers.

option(s):

Quick Change Chuck Adapter - 97181

Another adaptor, I find these very useful.

handy for using drill bits in your driving tools that have the quick-change feature.

Makita 3/8 in. Metal Keyless Chuck for Impact Driver keyless 3/8" chuck by Makita

 1/4" chuck by Milwaukee Tools

I keep these at-the-ready with the drill-driver tools.

These smaller size chuch adaptors fit nicely in my drill press, so as to use with small drilling bits.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_