Kreg Owners' Community

William Patterson
  • Las Vegas, NV
  • United States
Share on Facebook
Share

William Patterson's Discussions

Extension Cord Cart
3 Replies

I'm making a roll-around extension cord cart. One flat board 1 1/2" base with wheels attached. In the Center a 4x4" upright with hooks on it. Anybody made one of these, if so what is the best way to…Continue

Started this discussion. Last reply by William Patterson Oct 12, 2015.

Project 2 a Garden Cross
11 Replies

I want to make a CROSS out of 2x4s, glued and screwed together and I am not sure where to start. Do I glue two 2x4s (x2)... Has anyone else made a CROSS before.Thanks,Bill in Las Vegas<><Continue

Started this discussion. Last reply by Elizabeth Leveques Dec 30, 2015.

Kreg Rip-Cut
2 Replies

Now that I ordered it, does anyone know if the Rip-Cut will work on a Rockwell Versacut saw?Thanks in advance,Bill in Las VegasContinue

Tags: Rip-Cut, Kreg

Started this discussion. Last reply by Elizabeth Leveques Dec 30, 2015.

First Project Nightmare!!!
16 Replies

Hi,Small shop shelf. I got all my pieces cut out, sanded, put in my homemade 90 degree jig. Attached all the shelves to the right side of the storage shelf but when I went to pocket hole the second…Continue

Started this discussion. Last reply by Elizabeth Leveques Dec 30, 2015.

 

William Patterson's Page

Profile Information

Which Kreg products do you own?
Kreg Jig® R3 (Jr.), Micro-Pocket™ Drill Guide, Kreg Clamps, Kreg Cutting and Measuring Tools
How would you describe yourself?
Beginner DIYer
How did you learn about the Kreg Owners' Community?
Other
What's one interesting fact about you, your life, your garage, shop, or home?
I'm an old, 100% Disabled, Vietnam Vet who is just now (almost 70) taking up wood-working.

Comment Wall (5 comments)

You need to be a member of Kreg Owners' Community to add comments!

Join Kreg Owners' Community

At 6:57pm on September 10, 2015, james wilhelm said…
BILL you can use wood filler or a Kreg wooden pocket hole plug and sand off , JIM !!!
At 8:44pm on September 9, 2015, james wilhelm said…

HI Bill , one other thing  you may want to check is  that the collar is set on the 3/4 "  mark on the end towards the tip of the bit , JIM !!

At 8:38pm on September 9, 2015, james wilhelm said…

HI BILL , The Images and the post by the Kreg Rep.  should work with your K3 , the only other thing you may want to check is the true thickness of the board and make sure the little lip,s on the slider are hooked on the out side  edge of the board  when you drill the holes , if you have every thing set as per Images in post it should work and hold , JIM !!

At 11:30am on September 7, 2015, james wilhelm said…

HI BILL , Also welcome back , did not get many of them when we came back !!!  Sending you some pics. and info. on the cordless driver,s I use !!!  The one is a snap on  MD. # CTS - 561 and the other one is a Craftsman  Nextec    MD . # 320,17562, they both get into tight places !!  Was in the 199 TH . 3 RD and 7 TH.   , 68 to 69 , Have a good day and hope this helps , JIM !!

At 8:47pm on September 6, 2015, james wilhelm said…

HI Bill , also a Vietnam vet ,  did you drill the pocket hole on both end,s of the shelf,s ?   If so they do make a short driver bit ,  and you can also use a 1/4 " ratchet and socket to put the screw,s in the left side , also  they make some smaller cordless driver,s  that will help you out , craftsman dose have a few that are not to expensive , hope this helps you out , thanks for your service , JIM !!

 
 
 

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Pantry slides for heavy application

  Recently purchased two 96" tall pantry cabinets that are 23" deep that only came with two adjustable shelves and two fixed, (one at about 55" and one at the very bottom).  Shelf holes in the walls are drilled 2" O.C.  Like most store-bought…Continue

Tags: drawer, slides, pantry, pull-out, 75-Lb

Started by Paul Coon in General Woodworking Aug 11.

Miter Saw Recommendation 1 Reply

I’m looking to upgrade my miter saw. I’m willing to invest a good amount of money to get one with the precision pocket hole joinery requires. Would anyone like to offer a recommended model?

Started by Joe Racz in Beginners' Zone. Last reply by Scott Davison Oct 6.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 8 Comments

© 2021   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_