Kreg Owners' Community

Hi folks.

I'm trying to figure out the positioning of the Drill Guide for various material thicknesses, when the Drill Guide is used by itself (without Spacer Blocks) for repair work.


As I read it, the Drill Guide by itself or with Spacer Blocks is fine if the nominal thickness of the material is 1/2", 3/4", 1" thick or any larger size that is a multiple of 1/4".


But what if you don't have a Spacer Block, or enough Spacer Blocks, or if you're material thickness is not an even multiple of 1/4" ?


If I'm reading the instructions correctly, for material thicker than 1/2" the Drill Guide must be positioned back from the edge of the material by an amount that is determined by the actual thickness of the material. For 3/4" material the Drill Guide is moved back the width of one Spacer Block.


I have measured the Spacer Block as adding 3/8" to the height of the Drill Guide. So, in the absence of a Spacer Block being available...


For 1/2" material = Drill Guide is flush with end of material
For 3/4" material = move Drill Guide back 3/8"


So does it automatically follow then that...


For 1" material = move Drill Guide back 3/4"
For 1 1/4" material = move Drill Guide back 1 1/8"
For 1 1/2" material = move Drill Guide back 1 1/2"
For 1 3/4" material = move Drill Guide back 1 7/8"
For 2" material = move Drill Guide back 2 1/4"


And so on: add 1/4 inch to the previous value in the first column, add 3/8" to the previous value in the second column.


Am I on the right track? If so, I need to expand on that table to cover some intermediate thicknesses as well. For example, I am about to take on repairing several chairs where the nominal thicknesses of the material is 7/8". I think it would be useful to have a table where the first column increments by 1/8" for a range of material thicknesses.


My table would be in millimetres as Australia uses the metric system, but conversion is no problem.


Comments & thoughts?

Views: 1645

Reply to This

Replies to This Discussion

3 dozen views and no comments!

With settings being so important to success, surely someone has some useful input on this issue.

Kreg staff ???

Hello,

You are correct in your thoughts about the drill guide block stepping back in those increments, but the Kreg Jig is maxed out at 1-1/2" material thickness. You can use the jig on thicker materials but the longest screw available is 2-1/2". Please keep in mind the settings for the drill bit do not scale so easily and you will want to use one of the jigs to set the drill bit stop collar accordingly.

Thanks Ryan. I have now printed a table to keep with my Jig. Against material thickness, from 1/2" to 2" in 1/8" increments, it tabulates distance of Drill Guide Block from end of material, along with Screw Length for that thickness. Both millimeters and inches are shown.

I find it a handy quick reference when using the Drill Guide Block by itself. As you say, it is still necessary to set the drill bit stop collar with reference to the Jig markings. Measuring the distance-from-edge worked out fine for the 7/8" material I'm currently working with.

FYI, I started this because I only had one Spacer Block, which wasn't enough for the material thickness I was working with, and my local Kreg reseller is about an hour's drive from me and was out of stock of extra Spacer Blocks anyway. When I get my 3-D printer (within a couple of weeks hopefully) I'll look at creating a range of spacers for the various material thicknesses I encounter.

Maybe the Portable Drill Guide Base would be more value than using material in the 3d printer

https://www.kregtool.com/store/c22/kreg-jigreg-accessories/p108/por...

Sure, but what about a repair job where you're tightening up a loose joint, and you can't get the lip of the Portable Base over the end of the material to be drilled, because the gap between it and the material it's joined to is too small?

I've got this situation with the wobbly chairs I'm working on at the moment, and the amount of work would be considerably increased if I have to carefully open all the gaps so the lip of the Portable Drill Guide Base fits in.

But I can print very accurately sized spacer blocks to suit a number of material widths. Just grab the appropriate spacer out of the box, sit it on the material, and push the Drill Guide Block up against it. Voilà, exact positioning achieved.

HI  as far as the chair repair goes , I would use  the KREG  MINI  jig , if you have one , great for repair job,s  and not that expensive here ,hope this help,s , JIM !!

Sure Jim, would be handy if I had one, and next time I make the one-hour drive to the Kreg distributor there's a good chance I'll buy one.

However, even the Mini Jig may need to be spaced back from the edge according to material thickness.

By the way, going by this video https://youtu.be/ca1_aRRF17Q and the comments to it, it would seem that the default material thickness for flush mounting of the Mini Jig is 3/4", not 1/2" as for the normal K4 unit. Is that correct?

By the way, here is my table for the normal K4 jig:

If anyone sees anything wrong with that please advise.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_