Kreg Owners' Community

November 2010 Product Reviews (6)

Denver Woodworking show

w00t! Today I'm headed to the Denver Woodworking show! I'm all excited, I was hoping to have gone yesterday but had some "honey-do's" that needed to get done first in prep for our early Xmas gifts.

What makes me excited about attending the show is that as a new woodworker, I can get better exposure to all the cool stuff out there than say an afternoon in a single store. Plus there are a couple of seminars I'm pretty excited to attend, Jim Harvey's and the pen turning. I'm…

Continue

Added by Steven R. Hulse on November 21, 2010 at 11:02pm — 1 Comment

Ammo Crate Benches

Wow, it’s been a long time since I’ve written, but I have still kept woodworking, trust me. 2010 has been a whirlwind ride, that’s for sure. A new girlfriend, a new job, moving soon into a new townhouse, you name it. I didn’t forget about anyone, just had a lot on my plate this year.

One of the…

Continue

Added by Don Grubish on November 16, 2010 at 4:41pm — 9 Comments

Dremel Trio

I got sold via adds/web site/etc. I'll admit it- got suckered. This tool does nothing that several other tools (namely 'Roto Zip') , jig saw, router, etc won't do with patience and due care. I have a DeWalt VSR reciprocal saw that performs admirably with the right blade and speed control. If I were a 'tool collector' I'd not be disappointed for it does have some specific positives, although limited. In addition; an entire new set of accessories will need to be purchased at an outrageous (my… Continue

Added by Merrill Hayes on November 7, 2010 at 1:10pm — 3 Comments

My Review of Kreg Jig Master System

Continue

Added by Ian S on November 5, 2010 at 1:53am — 1 Comment

Grizzly Catalog

I remember when I was a kid I would always look forward to the Sears and JC Penny wishbooks. I would spend hours going over the pages of all the cool stuff, toys, musical instruments, women's underwear sections. Oh wait, I never did that! ;-)

 

Recently I got the big Grizzly catalog and it threw me back to those days as a kid. I immediately dropped all the other mail on my desk and went over to the couch and began flipping through those magical pages. I was whisked away to my…

Continue

Added by Steven R. Hulse on November 4, 2010 at 11:00pm — 6 Comments

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Concealed Hinge Jig Setting Confusion

The Kreg Concealed Hinge Jig has a setting for the distance from edge of the door to the nearest edge of the 35 mm cup hole. This can be set as 3, 4, 5, or 6 mm.Later in the instruction there is a table that converts the distance from the edge of…Continue

Started by Ken Kortch in Kreg Jig® Operation Oct 11.

Help with old Rip-Cut(tm)

I have an old Rip-Cut which I bought many years ago but did not set.  I seem to have lost the instructions, if I ever had them.I cannot figure out which bolts are match with the nylon-lock screws.This unit is old enough that the current instructions…Continue

Started by Sean in Other Kreg® Products Oct 4.

Product Reviews

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 1 Comment

Kreg Jig Dust Collection Attachment

1st impression when you hold this attachment in your hand:  "not much to it", Kreg sure is makin' $$ here.



Then I installed it.. perfect fit, leaves just enough room to adjust the setting screw on my K4.



Then the real test, hook…

Continue

Posted by Grampy Meyer on February 23, 2020 at 11:36am

© 2020   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_