I would like to see a flat spot on the shank of the bit to keep the collar from slipping while drilling. this has happened 2 times even though i tighten it.
I personnaly like the new case to hold all parts
Tags:
I would rather they went back chuck keys so you could tighten the bit properly.
The stop collar is slipping on the drill bit?? Try replacing it with a cup style. Should be able to get one at ACE for about 50 cents... ACE will probably charge a dollar for it though.
Gary - the ratcheting type keyless chucks hold pretty well.. problem is they aren't available on the cheaper drills; B&D, Ryobi, Skil.... The deWalts and Makitas have them though.
it is not the drill chuck that slips it is the depth guage collar. also i am not familar with a cup style (is that a collar
Cup point refers to the set screw that locks the collar. There are several different configurations of screws. Some hold better than otghers.
http://www.mcmaster.com/#set-screws/=f8wjct
ACE hardware will carry most.. that link is just info.
James Pittman Jr. said:
it is not the drill chuck that slips it is the depth guage collar. also i am not familar with a cup style (is that a collar
ok i appreciate it did not think about the allen set screw being what you were talking about. thanks John
John Schaben said:
Cup point refers to the set screw that locks the collar. There are several different configurations of screws. Some hold better than otghers.
http://www.mcmaster.com/#set-screws/=f8wjct
ACE hardware will carry most.. that link is just info.
James Pittman Jr. said:it is not the drill chuck that slips it is the depth guage collar. also i am not familar with a cup style (is that a collar
You no it is possible that you could take it to a grinder and hold the shaft sideways too stone and get a flat spot on shank so set screw could ride on that.Just a thought from a grandpa
Grinding a small flat, approx 1/8'', along the drill shank is very effective.
Grinding a small flat on drill bits is most effective, to prevent slippage---
especially effective with today's drills that have those keyless-chucks and smooth jaws.
If one doesn't have a grinder, a small ''flat'' can be added to a drill bit shank, using a ''mill file''.
When using a grinder, use care, DO NOT overheat the drill shank.
If it gets to hot to touch, frequently quench the shank in water,
That is what i have decided to do to mine
Ken Darga said:
Grinding a small flat, approx 1/8'', along the drill shank is very effective.
Grinding a small flat on drill bits is most effective, to prevent slippage---
especially effective with today's drills that have those keyless-chucks and smooth jaws.
If one doesn't have a grinder, a small ''flat'' can be added to a drill bit shank, using a ''mill file''.
When using a grinder, use care, DO NOT overheat the drill shank.
If it gets to hot to touch, frequently quench the shank in water,
thanks for all the answers ,i appreciate it
Ken Darga said:
Grinding a small flat, approx 1/8'', along the drill shank is very effective.
Grinding a small flat on drill bits is most effective, to prevent slippage---
especially effective with today's drills that have those keyless-chucks and smooth jaws.
If one doesn't have a grinder, a small ''flat'' can be added to a drill bit shank, using a ''mill file''.
When using a grinder, use care, DO NOT overheat the drill shank.
If it gets to hot to touch, frequently quench the shank in water,
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service