Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
Shop Fox w1820 ReviewWe went this morning to pick the saw up. The packaging was amazing and things were greased just like I expected. 3 hours from getting home… Started by justin waldron |
0 | Mar 5, 2011 |
Safety.I would like to take this oppertunity to respond to all of the Kreg Community for all the kind words and all the well wishes that have come… Started by William Steinfeldt |
0 | Mar 2, 2011 |
Harbor Freight Dust Collector/Long Ranger RemoteI have done a little research and it seems like the Long Ranger Remote will work with the Harbor Freight Dust Collectors? I don't know if… Started by justin waldron |
9 |
Mar 1, 2011 Reply by justin waldron |
Any brick and mortor stores that still have K3 in stock?Any brick and mortor stores that still have K3 in stock? Started by Gary roofner |
3 |
Feb 27, 2011 Reply by Coach Rick |
new Kreg K4MS commentsthis is a great forum and checking out others fine projects is inspiring! I have some comments on my new purchase the K4MS. I have not used… Started by interpon |
2 |
Feb 26, 2011 Reply by Wayne Mclellan |
staplesI am repairing some draws that were stapled together and in too deep to remove, will the damage the drill bit? Started by Bill Schafer |
1 |
Feb 25, 2011 Reply by Geoff Simpson |
230v electrical help!!I hope there's an electrician out there, because I am not. I have a 220v outlet in my garage for my table saw etc. I just recently ordere… Started by justin waldron |
24 |
Feb 24, 2011 Reply by justin waldron |
Cabinet DrawersIs there a rule of thumb on making cabinet drawers. Not sure on how to measure to get correct drawer size to fit rollers. I was wondering i… Started by Jack Harvey |
22 |
Feb 22, 2011 Reply by Ken Darga |
Kreg Jig caseHi, All: Some place I saw a picture of a case for carring and storing Kreg pocket hole jigs and the accessorys, that when opened up, made a… Started by Lowell D Sites |
2 |
Feb 22, 2011 Reply by Lowell D Sites |
Downdraft table plansDown_Draft_Ezplan.pdf I was looking at Rockler this morning and noticed they had a free plan for a downdraft table so I wanted to share t… Started by justin waldron |
8 |
Feb 22, 2011 Reply by Jay Boutwell |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service