Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
First project questionsI am making my first project with my newly purchased Kreg Jig Jr. I am going to attempt to make a set of cornhole boards. I found plans onl… Started by April |
6 |
Sep 27, 2013 Reply by Dan S |
wood glue?Do you always use wood glue? I built my first project, a workbench (profile pic) and I did not use it. Now I'm wondering if I should have… Started by Megan |
8 |
Sep 25, 2013 Reply by Ken Darga |
Building a roofI am interested in getting a Kreg jig kit; currently looking at the K4MS, and the first project I have in mind is putting a "roof" on my wo… Started by Howard P Reynolds |
2 |
Sep 21, 2013 Reply by Howard P Reynolds |
Drawer SlidesQuick question about drawer slides. I want to add a drawer at the bottom of this LP storage unit . Its 18 1/2 inches from rear to where the… Started by Matt |
2 |
Sep 19, 2013 Reply by Jay Boutwell |
First time user ? (Barn Wood)The wife has ask me to build a table/cabinet. I have a colection of oak barn wood that I plan to use. Most of the wood is rough cut 2"X 6"a… Started by Tim Lucas |
10 |
Sep 19, 2013 Reply by Russ Haynes |
What is the difference between Particle Board and MDF?I'm just wondering what the differences are between particle board and MDF? MDF is more expensive and I was wondering why. What applicati… Started by Lorrie |
30 |
Sep 14, 2013 Reply by Ken Kortch |
Master System Carry Case.I just bought the Master System. Is there a special way to load all the tools in the case? It didn't come with "packing" instructions....… Started by Doug Hemingway |
0 | Sep 13, 2013 |
ANYONE USED THESE MILLER DOWELS?Started by michael evans |
3 |
Sep 11, 2013 Reply by Ken Darga |
Joining angles?Hi, all. New user, and fairly new DIYer. I'm tackling the "Little Cottage Loft Bed" from Ana White's website as my first "all-kreg pocket… Started by Jim |
2 |
Sep 9, 2013 Reply by Russ Haynes |
RIPCUT UK .Anyone know if the ripcut available in the u.k. yet. Started by michael evans |
16 |
Sep 8, 2013 Reply by Ken Darga |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service