Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
End Table PlansHi Does anyone have or know where I can find end table plans with a drawer and shelf? I have looked on google and not gotten far. Thanks… Started by Jerry Irk |
1 |
Mar 21, 2018 Reply by KregRep |
K4 Jig Clamp ScrewHi, I'm new to the site so my question may be a kinda stupid one. I recently purchased the K4 master jig set for a project I'm working on.… Started by John Bilton |
4 |
Mar 15, 2018 Reply by Glen S |
Pocket Hole Angle to plane of entry into lumber.Hi fellow Pocket Holers, Please can I have the above angle. It can be the angle to the plane of entry or to the vertical. With this informa… Started by Eamon McElduff |
0 | Mar 5, 2018 |
Tapered Table LegsFirst of all, thank you for the add! In my lifetime, I've built from scratch: a play structure, two patio covers, a large deck, and a coup… Started by Pamela Anders |
7 |
Mar 4, 2018 Reply by Scott |
Finishing, what works for meHopefully this will help others, finishing has been one of the things that I have struggled through the years and I have a few tips that wo… Started by justin waldron |
0 | Mar 4, 2018 |
Phishing alertLooks like you got some bad apple(s) here, namely a "Sarah Micheal' that spams profile(s) about being a rich dying widow wanting to distrib… Started by Doc JL |
1 |
Feb 26, 2018 Reply by Craig Mayhan |
Pneumatic conversion pocket holeDoes anybody have a parts list to change the pocket hole rear clamp to pneumatic conversion. I hate having to reach around back to clamp th… Started by Michael B |
2 |
Feb 19, 2018 Reply by KregCS |
Only one screw per joint?Hi all, I'm building a large picture frame (about 2' x 3') that will hold a piece of radiator cover to display pins. Using 1x3 flat stock… Started by Michele |
2 |
Feb 3, 2018 Reply by Michele |
2x4 helpI am building a work bench. I am using 2x4 for the frame. I will be using a 3/4 inch MDF for the top. What screws and settings do I need to… Started by Trent |
4 |
Jan 31, 2018 Reply by Trent |
Kreg Jig K5 problemI have been having an issue with the K5 jig. Sometimes when I am drilling the pocket holes at 3/4" it seems like the drill bit hits the dep… Started by James Smith |
15 |
Jan 28, 2018 Reply by Barry G. Sumpter |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service