Tags:
Charlie,
I own Ridgid 18 volt Cordless. I got them from the Home Depot Store. What I like is the tool and battery's are life time, as long as you register them. When you buy a kit that is. I have a 1/2 hammer drill driver. Works great on anything I have done.
Joe
I prefer a corded drill for drilling and a battery drill for fastening. The corded drill is plugged into a device that turns on the vacuum when the drill is running.
I usually use a corded drill for long projects with a lot of drilling but my Milwaukee cordless has no problem drilling lots of HD holes.
I use my Milwaukee brushless drill. It has plenty of power!!!
I like the M18 Fuel drills. These are brushless drills that deliver a lot of power. The Li-On batteries last a long time, too. I got the set with the drill and driver. I use the drill to drill the holes and the driver to put the screws in.
My local Home Depot has them on sale this week for Father's Day. I suspect Lowes may, too. They are expensive but I think they are worth it.
My only problem was going from the Black and Decker, which I like, to the more powerful drill, I have to be very careful not to drive the screws in too fast and strip the holes out.
Hi Charlie ,i am in the U.K. screw fix doing a deal on a Bosch battery drill gsb 18 2 li with 4.0 ah battery £99.99 more than enough power . I use Hitachi battery drills again from screw fix model dv 18 dgl/jc comes with two 1.5 ah batteries never found these batteries to lack power for all my woodworking tasks ,and i have had these drills 5 years now . I HAVE A Makita impact drill also and i find it to fierce for alot of woodworking applications ,hope this helps .
Glad to help Charlie , if you find it to powerful for some applications turn the clutch down a notch or two go steady.
Hey, you should see if you can get your hands on the Fein ASCM 4x speed drill for all situations.
It comes with 2 x 18v 5.2ah batteries, but they are light and they really drive home any screw.
We have used them for drilling straight into oak a m10x600mm screw! Brilliant piece of kit if you can find a FEIN dealer near you. See this for a little teaser. Fein ASCM 18QX
Didn't realise you were in the UK, I sell them in Kent ;-)
Charlie Roberton said:
Thank you. I'm in the UK but will have a look for any Father's Day deals this weekend. Good tip on the screws thanks.
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service