Kreg Owners' Community

Joe Collins
  • Beaver Dams, NY
  • United States
Share on Facebook

Joe Collins's Page

Latest Activity

Joe Collins replied to Bob Molloy's discussion 'Multipurpose Work Center Parts List'
"Bob,    The drawing never specs. out for shelf's inside the cabinets. There is only specs for 2 upper 2 lower. I would have to say putting shelf pin hole inside the cabinets, would be where the other 3/4 plywood would be…"
Apr 21
Joe Collins posted photos
Jul 15, 2016
Joe Collins commented on Joe Collins's photo


"I  just seen this table looks like it only has three legs will have to add another picture. Joe"
Jul 15, 2016
Joe Collins replied to Frank Gonzalez's discussion 'Router Table Question'
"Using the starter pin and a bearing router bit. Depending on the length make sure the whole piece is supported. Mark the ends then start as close to the end as possible. Stopping where you need it to stop. You can go a short distance in the opposite…"
Jul 13, 2016
Joe Collins posted a photo


Night StandI built this using my Kreg Jig. The legs are 1 1/4" Spindles for a Stair railing. I just cut the one end off. The sides and back are inset 1/2" making the inside flush. The draw is made from 1/2" plywood using the Kreg jig. The draw face…
Jul 13, 2016
Joe Collins replied to Charlie Roberton's discussion 'Drill recommendation for hd jig'
"Charlie,    I own Ridgid 18 volt Cordless. I got them from the Home Depot Store. What I like is the tool and battery's are life time, as long as you register them. When you buy a kit that is. I have a 1/2 hammer drill driver. Works…"
Jun 14, 2016
Joe Collins posted photos
Jun 14, 2016
Joe Collins posted photos
Jun 9, 2016
Joe Collins commented on Marshall Moneymaker's album


"Nice job. I built one like it a few years ago. I just put a hole in the side with a adjustable hole cutter. I set it for my 2 1/2" hose. I used a peg board for the top. Joe"
Jun 1, 2016
Joe Collins commented on Scott @'s album

2x4 Flip Top Workbench Cart

"   Hello,   I built one close to what you have built. I have it setup so the out feed of my planer, is the same height as my work bench. The other side I have a isolating spindle sander. This way there off the floor and not stored…"
Feb 10, 2016

Profile Information

Which Kreg products do you own?
Kreg Jig® R3 (Jr.), Shelf Pin Jig, Rip-Cut™ Saw Guide
How would you describe yourself?
Intermediate Woodworker
How did you learn about the Kreg Owners' Community?
In-Package Brochure
What's one interesting fact about you, your life, your garage, shop, or home?

Joe Collins's Photos

  • Add Photos
  • View All

Comment Wall

You need to be a member of Kreg Owners' Community to add comments!

Join Kreg Owners' Community

  • No comments yet!

Need Help?

For Technical Support, call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 

Popular Posts & Projects 


  • Add Videos
  • View All


problem joining a table leg to the base 3 Replies

Started by Bradley Smith in Beginners' Zone. Last reply by Trace Farthing Sep 12.

Design help 3 Replies

Started by Michael B in Beginners' Zone. Last reply by Ken Darga Sep 12.

Joining 5/4 boards 1 Reply

Started by Kent in Beginners' Zone. Last reply by Ken Darga Sep 3.

Drilled wrong depth 1 Reply

Started by Robert yost in Beginners' Zone. Last reply by Ken Darga Aug 31.

Proper spacing of pocket holes for heavy duty drawers 3 Replies

Started by Donna Osburn in Beginners' Zone. Last reply by Donna Osburn Aug 24.

Product Reviews

Kreg Mobile Project Center

I just picked up my new Kreg Mobile Project Center Item #KWS1000.

Wow!  I set it up in my basement and it is great addition to my Kreg items.  I was viewing a video where a review on this fine product was being made, which prompts…


Posted by John Tomkinson on May 5, 2017 at 5:34am — 2 Comments

Handy jig to hold and push plugs in!

Takes 10 minutes to make this handy accessory for your Kreg gear! Home made plug pusher.

Posted by Dave Stanton on March 31, 2017 at 5:53pm — 2 Comments

© 2017   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service