Kreg Owners' Community

I am either making two benches and a table OR adding to my scrap pile. Regardless, I would like to know how far apart to space the holes for the table top or bench tops. I am using 2.x 4's for the bench and the boards are 41" long, then I"ll add an breadboard to each end. The table top is aprox. 63" long. The long boards will be slightly less then 48" (i am splitting 3 - 2 x 8 and 1 - 2 x 10 in half, so will square the ends off as skinny as I can, then cut the remaining piece in half) anyhow...they will be slightly less then 48 and will have 2.x 8's as the bread boards on each end. Not sure why they are called bread boards.

For the tabletop  I'll be alternating the 2 x 8's with the 2 x 10s (5 pieces total) What should the spacing be for the pocket holes on the longer pieces? and on the three center boards of the 5, do I only pocket hole on one side to the next board, or should there also be a couple coming from the board I am going into. what about the two end boards, or breadboards?

did that make any sense?

Views: 28005

Reply to This

Replies to This Discussion

Hi Debora,

As a general rule when gluing panels, we recommend a screw about 2" from each end, and then screws spaced every 6" to 8" along the rest of the board length. You can put screws just in one side of each joint. You'll find this information on your SkillBuilder DVD under the "Edge Joining" section.

I'd probably follow the same spacing for adding the breadboard ends. One thing to note: I'm not sure if you're gluing boards together or not. If so, on the breadboards I'd add glue near the center of panel, but not at the ends. That's because the boards in the main part of the panel will expand and contract in width some due to seasonal humidity changes. The breadboard ends, though, won't expand and contract in length. So, by just screwing on the breadboard ends or by gluing them just at the center and using only screws on the rest, the wood movement wont cause cracks, splits, etc.

If you're using 2x4s (1-1/2" actual thickness) you should have your jig set for 1-1/2" thickness, the drill bit stop collar at the position for 1-1/2" stock, and assemble the joint with 2-1/2" screws, as detailed in your Quick Start Guide booklet.

The breadboard term comes from the original construction. Bread boards were traditionally built with boards at the end positioned 90 degrees to the rest of the panel. That way it was easy to cut holes for carrying handles, etc. So, today when we build a table top that way, it gets referred to as a breadboard-style top, or a top with breadboard ends.

KregRep

Forgot to say, the breadboard ends also helped to keep the panel flat (and still do). With a breadboard that got hot, moist bread placed on it, there was a tendency for the panel to bow. The breadboard ends, running crossways, help keep the panel flat. That's not as big of a deal with the table top or bench top, since it will be attached to the base. In these applications, a breadboard end is more of an aesthetic choice.

KregRep

Thank you for all that. I love hearing how something became what it is. Right now, I am still trying to figure out how to square up the table, as when I measure crossways, its about 1" different. I am pushing the corners with the  help of my hubby, but would love to do it with no help. I think I'm going to dig around for one of the ratchet straps we use for our tree stands, to hold it in place while I screw the corners in. Its going to be a rustic table, so it probably won't matter a whole lot if its out a little, but I still want to try and get it as close as I possible can to square. I realize its tougher when you are using lumber, but I can't  help but over analyze this whole process. Then will begin cutting my tops.  The wood is still super heavy, so i am not sure if its ok to just proceed or wait longer. Its been almost two weeks that it has sat indoors to help dry.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_