Kreg Owners' Community

I recently bought the micro jig for 1/2 inch material.  I've never got it to work correctly and I've followed the directions to the letter.  I've tried both 1 inch and 3/4 inch screws.  My screws are not coming out in the center of the workpiece and usually they through my work piece..  I tried the Kreg tech support but was practically insulted and told my material wasn't 1/2 inch thick.  Has anyone else had this issue?  I have the regular size jig and have never had a problem but the micro jig has not really served me well.  I look forward to solutions to my problem.

Views: 4871

Reply to This

Replies to This Discussion

Personally, I don't think it's funny.

When I measure or spec out 1/2'', it's a half-inch, not something else.

I know it sucks, that they can't make 1/2'' PW a 1/2 inch.

That drives me crazy.

Just like hardboard (as in masonite)---

lumber yards mark their goods  1/4''---

and it's not 1/4''.

When I've ordered 1/4'' stock, I get 3/16 to 7/32''!

Go figure.

PS---years ago, 1/2'' PW was 1/2''.


RCW said:

Funny because most "1/2" wood is not 1/2 inch when you measure it.

Lisa,

The narrow end of the clamp, can be machined (ground and filed) down to fit into the smaller dia pilot hole.

Lisa Zanni said:

Does anyone know if Kreg plans to come out with a *right angle Clamp* for the Micro Jig.  My right angle clamp end is too large to fit in the holes that a micro jig makes.

After talking with our associate in the woodshop, one possible cause of the issue you are having is due to the position of your pocket holes.  With ½” material, if you drill your holes toward the outer edge of the joining piece it will sometimes come through the bottom since there is not enough wood to grip on to.  However, if you turn your piece around so that the pockethole will be going towards the middle of the board it will work without any issues.  We are currently working with Marketing to get this information put in the manual to help explain this situation.  This situation only comes up with 1/2" since it is less forgiving due to its small thickness.  I have attached a rough sketch to this posting that will hopefully help explain this. 

Another possibility is to make sure that the screw is following the pilot hole in your pocket hole.  If you are not careful, you can drive your screw without following the pocket hole hence changing the postion of the screw.  If the angle is changed due to this it can greatly impact the integrity of the joint. If you have any other questions please let us know.

I understand that if the screw is exiting off center it will work when you drill from the outside (correct image above). 

The problem is for repair work and some assembly projects you have to drill the pocket holes from the inside (incorrect image above). My issue is that I have a wall on outside so I can not drill or screw from the outside. With the normal size kreg jig I do not have a problem with an inside pocket hole since the screw seems to always come out of the center of the board.

It appears that with the current angle of the micro jig you can not repair or construct an object using pocket holes in an inside corner and 1/2 plywood unless you can allow the screw heads to not be flush with the surface.

Very true, it is easy to not get the screw in the right position. you have to really make sure it's in the hole the right way.

HEY ! ! ! Can't we all just get along?

weird - conversation here.... dating service ? weird. 

i never ever asked for that reply and frankly shes not my type.

Look at the broken English sounds like a Nigerian scam to me.

Howdy!

I find pocket hole joinery, Kreg and or others have limitations when it comes to 1/2" thick material. I wouldn't buy one even for repairs for small drawers. Your best bet is to completely rebuild the drawer and install the old face.

Lockng rabbit joints and glue are the old but true solution to building draws as I see it a good working knowledge of old school wood working is still useful today. I'm glad I didn't buy the 1/2" Kreg pocked hole joiner and don't intend to. My standard Kreg pocket hole joiner is a useful tool but will never be the answer to all my wood working problems. Good luck and may God bless.

Sincerely,

JosephEsquivel

I am having the same problem with the 1 half inch material using the regular jig I'm interested to see what responses you get . Thank you for asking this question maybe I can get some help with it too.

Used mine for the first time last night. Worked great.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_