Tags:
Hi Dan,
had a similar quesiton earlier this year when I replaced my old work bench. I am originally from Toronto, but now live in Virginia. We get a lot of humidity here and my shop is in my garage. When I lived up north, all my shops were in the basement and didn't have the moisture issue.
Personally, I do not like MDF. I find it can be really hard on saw blades. It also has a habit of denting and it does not hold up to moisture very well. If it gets wet, it will bubble. If it gets soaked it can swell.
What I have done in the past is use a sheet of 3/4" plywood. Then, I laminate that with a 1/2" or 3/4" of oak or birch plywood. I do not glue down the top layer and attach from the bottom with screws. Then, when the top gets beat up, you can take it off and replace it.
As far as finishing goes, I prefer natural oils over stains or paints. They are easy to apply and once I year I reapply oil to my bench if needed. I have made a few benches from of all different sizes. If you have any questions or want any ideas I am happy to help. My email is rundle3@verizon.net
Workbenches are my favorite projects. The wood is relatively cheap (I use 2x4's and 2x6's) and you can try some different joints and techniques.
Hi Dan,
had a similar quesiton earlier this year when I replaced my old work bench. I am originally from Toronto, but now live in Virginia. We get a lot of humidity here and my shop is in my garage. When I lived up north, all my shops were in the basement and didn't have the moisture issue.
Personally, I do not like MDF. I find it can be really hard on saw blades. It also has a habit of denting and it does not hold up to moisture very well. If it gets wet, it will bubble. If it gets soaked it can swell.
What I have done in the past is use a sheet of 3/4" plywood. Then, I laminate that with a 1/2" or 3/4" of oak or birch plywood. I do not glue down the top layer and attach from the bottom with screws. Then, when the top gets beat up, you can take it off and replace it.
As far as finishing goes, I prefer natural oils over stains or paints. They are easy to apply and once I year I reapply oil to my bench if needed. I have made a few benches from of all different sizes. If you have any questions or want any ideas I am happy to help. My email is rundle3@verizon.net
Workbenches are my favorite projects. The wood is relatively cheap (I use 2x4's and 2x6's) and you can try some different joints and techniques.
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service