Kreg Owners' Community

Ben Socratous's Discussions (34)

Discussions Replied To (32) Replies Latest Activity

"This look like it has potential. I see one major flaw in the design in its current f…"

Ben Socratous replied Feb 15, 2012 to Introducing the Kreg Rip-Cut™

153 Nov 22, 2013
Reply by Jeff Hayes

"I'm using these http://www.carbatec.com.au/carba-tec-low-profile-plastic-bench-dogs_…"

Ben Socratous replied Mar 6, 2011 to new workbench construction

7 Mar 6, 2011
Reply by Ben Socratous

"Well, between a thousand and one other projects, and being put on shed time sanction…"

Ben Socratous replied Mar 5, 2011 to new workbench construction

7 Mar 6, 2011
Reply by Ben Socratous

"What about using multiple flip stops? Set them to their respective locations, then p…"

Ben Socratous replied Jan 29, 2011 to Jigs and Fixtures.

1 Jan 29, 2011
Reply by Ben Socratous

"I wish I had this problem! Being in Adelaide, over the christmas/new years holidays…"

Ben Socratous replied Jan 15, 2011 to workshop heat

6 Jan 18, 2011
Reply by kenny from Sundre

"Ok, this project finally has gained some more momentum! I had planned to get it all…"

Ben Socratous replied Jan 14, 2011 to new workbench construction

7 Mar 6, 2011
Reply by Ben Socratous

"Well, having a friend working at a bank sure has its advantages! My credit card is n…"

Ben Socratous replied Dec 17, 2010 to Photos of your last woodworking purchase!

71 Feb 5, 2011
Reply by ray vile

"Nooooooooooooooooo on the epoxy! Epoxy starts to lose its integrity above 90ish degr…"

Ben Socratous replied Dec 6, 2010 to Can poly handle the heat

3 Dec 6, 2010
Reply by Ben Socratous

"I do most of my work with mdf, and I have found that dust extraction on the jig is a…"

Ben Socratous replied Nov 14, 2010 to burning up a drill bit while working with mdf

11 Nov 26, 2010
Reply by ray vile

"I try to make that not necessary when building them as much as possible, but having…"

Ben Socratous replied Aug 4, 2010 to Kreg Jig used in my new speaker system

10 Dec 30, 2015
Reply by Elizabeth Leveques

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Rip-cut ACS plunge saw

Just got a rip-cut and installed my Bosch saw haven't used it yet but saw was a good fit. Got the original ripcut and didn't really like it had trouble cutting straight. New one has several improvements should make it work much better. especially…Continue

Started by William Burt Brown in General Woodworking Mar 17.

Is the screw driver impact drill rater?

Is the screw driver impact drill rated?Continue

Started by Bob Naylor in Beginners' Zone Mar 10.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 4 Comments

© 2021   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_