Hello All,
I am fairly new at woodwork and have a slight problem. I have built a headboard and a bed frame. Both were built using the Kreg Jig (I love this tool !) I purchased all the wood at the same time. I built the headboard and stained it no problem. I have now built the bed frame and stained it. The problem is the two items are not the same shade now. I used the same can of stain. I built the two items about three weeks apart.The bed frame is quiet a bit darker..now what do I do..??
Should I have built both items then stained them both ?
any suggestions would be very helpful,
Derrick Williams
Tags:
Two things occur to me. First, did you use stain sealer on both pieces? Usually, without stain sealer pine will become blotchy but it could also account for different absorbtion between the two pieces.
Second, Was the headboard sanded to a finer grit than the bed frame, or, sanded more? Sanding smoother produces a smooth surface but also tends to fill the grain slowing stain absorbtion.
Derrick Williams said:
Both pieces were built with pine. I'm thinking one may have been white pine and the other yellow pine . Neither piece
Was put in the sun to dry.
Was the headboard exposed to direct sunlight when drying ? ...and yes it is best to finish any "set" pieces at the same time if possible...you may also want to try wood conditioner before staining, especially if on pine.
The best wood conditioner is "Charles Neil's Blotch Control"
You can get it here.
http://shop.charlesneilwoodworking.com/Charles-Neils-Pre-Color-Cond...
Can't say enough good about it. It's more expensive than others, but the results are well worth it.
Craig Sims said:
In the past I have had the same problem or something simular. My project comes out darker than I want, or it is supposed to have a red tent and it is brown. What wood conditioner do you recommendand where do I buy it?
Mike Robson said:Was the headboard exposed to direct sunlight when drying ? ...and yes it is best to finish any "set" pieces at the same time if possible...you may also want to try wood conditioner before staining, especially if on pine.
The best wood conditioner is "Charles Neil's Blotch Control"
You can get it here.
http://shop.charlesneilwoodworking.com/Charles-Neils-Pre-Color-Cond...
Can't say enough good about it. It's more expensive than others, but the results are well worth it.
Craig Sims said:In the past I have had the same problem or something simular. My project comes out darker than I want, or it is supposed to have a red tent and it is brown. What wood conditioner do you recommendand where do I buy it?
Mike Robson said:Was the headboard exposed to direct sunlight when drying ? ...and yes it is best to finish any "set" pieces at the same time if possible...you may also want to try wood conditioner before staining, especially if on pine.
HI bennett....sorry for not responding sooner.
I have always used Minwax products...I have good luck with them.
Craig Sims said:
In the past I have had the same problem or something simular. My project comes out darker than I want, or it is supposed to have a red tent and it is brown. What wood conditioner do you recommendand where do I buy it?
Mike Robson said:Was the headboard exposed to direct sunlight when drying ? ...and yes it is best to finish any "set" pieces at the same time if possible...you may also want to try wood conditioner before staining, especially if on pine.
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service