Kreg Owners' Community

What's up with Kreg having no warranty on the Kreg Clamp?  Mine had the inside threads strip out from normal use so I sent Kreg an e-mail asking if the clamp was under any kind of warranty and was told the clamp is not a warrented part. Anybody else run into this problem with the clamp?

Views: 1756

Reply to This

Replies to This Discussion

My Kreg clamp recently stripped the threads too. Did you have any luck or have you found any similar products with manufacturers that will stand by their product?

I had no luck. Was told by Kreg there is no warrantee on this. Couldn't find anything similar so I just replaced it with a new Kreg clamp. Hopefully they've improved the thread design and this one will last a bit longer.

Tom said:

My Kreg clamp recently stripped the threads too. Did you have any luck or have you found any similar products with manufacturers that will stand by their product?

Thanks for the warning. I always thought those clamps were way over priced. I would not have bought another one. What makes you think they improved it?

Not a thing. I said I hoped they improved it. I looked around and couldn't find anything out there that was similar made by someone other than Kreg.

Hi Terry - would be helpful to note which clamp. Rockler carries 9 different Kreg clamp configurations.

http://woodworking.rockler.com/nav/cat1/shop-by-brand/cat2/shop-by-...


Terry Miles said:

Not a thing. I said I hoped they improved it. I looked around and couldn't find anything out there that was similar made by someone other than Kreg.

The best thing to do, to reduce friction and wear, is to add ''grease type lube'' to the threads.

If the threads appear dry, apply some lube.

Use spray-type lithium lube, in the areas not readily visible---such as down inside the threaded mechanism.

WD40 offers lith lube in a spray can with nozzle---for expended reach. 

Lube makes for easier turning---during tightening and loosening.

Hi Ken - I agree that lubrication helps, especially with the el cheapo clamping pliers that are the norm in my shop. I don't really care much for the grease type lubes though, usually opting for dry lubes like spray graphite.

Ken Darga said:

The best thing to do, to reduce friction and wear, is to add ''grease type lube'' to the threads.

If the threads appear dry, apply some lube.

Use spray-type lithium lube, in the areas not readily visible---such as down inside the threaded mechanism.

WD40 offers lith lube in a spray can with nozzle---for expended reach. 

Lube makes for easier turning---during tightening and loosening.

Finishing wax works great for lubing threads and doesnt clump and grab every piece of dust and dirt in the room...

I purchased a new machine today, that has an adjustment feature, similar to the threaded mechanism in the Kreg clamps---

the adjust was stiff/not easily rotated---

lots of resistance was felt while turning

_the threads were not clean

_the action was not smooth, for this type of mechanism---

_the threads were dry---no visible lube.

  Upon close examination of the exposed male threads, they were not cut or formed smooth---

''dry lube'' WAS NOT effective.

After applying lith-grease, to the first 3 threads, the action worked smoothly and

the adjustments were easy. 

  When to use white lithium grease:

Use WD-40 Specialist Protective White Lithium Grease where a thick lubricant film must cling and remain in place on horizontal and vertical surfaces. Excellent for metal-to-metal lubrication.

My issue was with the premium face clamp. I used it a few times before it stripped. I also have the 90 degree clamp but have not had an issue with that one yet...knock on wood



John Schaben said:

Hi Terry - would be helpful to note which clamp. Rockler carries 9 different Kreg clamp configurations.

http://woodworking.rockler.com/nav/cat1/shop-by-brand/cat2/shop-by-...


Terry Miles said:

Not a thing. I said I hoped they improved it. I looked around and couldn't find anything out there that was similar made by someone other than Kreg.

Seems like these would do for a face frame clamp... just don't have the pretty blue handle covers.

http://www.amazon.com/Vise-Grip-18-6SP-Locking-Clamp-Swivel/dp/B000...

Tom said:

My issue was with the premium face clamp. I used it a few times before it stripped. I also have the 90 degree clamp but have not had an issue with that one yet...knock on wood



John Schaben said:

Hi Terry - would be helpful to note which clamp. Rockler carries 9 different Kreg clamp configurations.

http://woodworking.rockler.com/nav/cat1/shop-by-brand/cat2/shop-by-...


Terry Miles said:

Not a thing. I said I hoped they improved it. I looked around and couldn't find anything out there that was similar made by someone other than Kreg.

Well, Good News. I had a Rep. from Kreg e-mail me directly, and was told they most certainly do Warrantee their products, and that they would be sending me out a replacement immediately. Thanks Kreg!!!

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Pantry slides for heavy application

  Recently purchased two 96" tall pantry cabinets that are 23" deep that only came with two adjustable shelves and two fixed, (one at about 55" and one at the very bottom).  Shelf holes in the walls are drilled 2" O.C.  Like most store-bought…Continue

Tags: drawer, slides, pantry, pull-out, 75-Lb

Started by Paul Coon in General Woodworking Aug 11.

Miter Saw Recommendation 1 Reply

I’m looking to upgrade my miter saw. I’m willing to invest a good amount of money to get one with the precision pocket hole joinery requires. Would anyone like to offer a recommended model?

Started by Joe Racz in Beginners' Zone. Last reply by Scott Davison Oct 6.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 8 Comments

© 2021   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_