Kreg Owners' Community

Tomorrow I will begin constructing the Shop Vacuum Cart found on the Kreg "Build Something," website. https://www.buildsomething.com/plans/PE821DAA69C097FAA/Shop-Vacuum-...

I do not have Kreg right angle clamps and right now I do not want to invest in them. Does anyone have any other suggestion for how I can glue up and use pocket hole screws to make sure this project turns out well?

Thanks.

Views: 2434

Attachments:

Reply to This

Replies to This Discussion

Use bar or pipe clamps.

Thanks. I was planning on doing that but was not certain it would work. I wish I had two or three of the right angle clamps. I have a number of other Kreg products and they work really well. I just cannot afford to purchase new clamps right now. 

Ken Darga said:

Use bar or pipe clamps.

Place "snippets" of wire brads between the joined members, so as to increase resistance to slippage of the joints when clamping and assembly. 

WorksForMe.

I am not sure I understand. Do you mean to install wire brads into one piece of lumber and leave a small tag end hanging out so that when you clamp the two pieces together it will press the tag end of the brad into the second piece? If so, it sounds like a great idea!

Insert the"tip" of a wire brad, 1/16 to 1/8" inch into the wood surface, using a brad pusher or a small tap hammer

Next---use "diagonal" cutting pliers---

place the flat side of the plier on the wood surface, with the pliers opened all the way, 

and slide the plier over the exposed brad sticking up out of the wood.

Next, close the pliers---squeeze real hard and cut-off the brad extending above the surface.

You should see a shinney looking thingy protruding from the surface.

This is what I call a "snippit"---like in "snip-it".

A couple of such snippits should suffice.  

For larger lumber material, you can use a finishing nail.

Cut finishing nails the same way, but use larger size diagonal cutters, like "lineman's pliers" for cutting heavy wire or cables.

There are countless ways to help with clamping / holding the pieces together during assembly.

Here's one from a search on "corner clamping plans" ...

Wood magazine - Right-angle brace -

Izzy Swan also has a couple of ideas too worth looking up

That is slick. I went out and built a smaller version. I will build the larger version next week (after I purchase a couple of sheets of birch baltic for another project.

Another approach I've seen on a youtube video about building cabinets is to drill the pocket holes, and then use a pin nailer to hold the material in place while you insert the pocket hole screws. They really just keep the material from slipping. The pin nails are thin enough to flex as the pocket hole screw seats.

ADDED: I should mention that the same video show him making very shallow dadoes and rabbets to make placement of the material easier, and then he mentions that for 3/4" plywood he uses 1" pocket hole screws rather than 1-1/4" screws - commenting that he wishes Kreg made 1-1/8" screws. The video is named "Simple Cabinet Construction, Part 1: Story Poles & Boxes". Sorry, I can't create a link here because of computer issues, but I found the video useful.

Line up your joints & shoot some 1 1/4" brads into the adjoining piece. Then run the screws in. It's just a shop vac cart.

Lovely DIY video on the Right Angle clamps. Thanks Jack Anderson!

Good question really. Had to use 5 clamps of various kinds and sizes yesterday!

Was joining oak rails for a face frame. Like to use glue on these joints and they want to move a little.

The plywood corner square/clamp looks great. Will definitely make some of those up.

tx, Ed

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Hard time pocketing 2x4 2 Replies

Hi all,Fairly new kreg user but have had no issues with past small projects using 1x4, 1x6,etc.  Starting a laundry pedestal build that uses 2x4 with pocket holes on te cross braces for top and bottom.  Setting jig on 1-1/2 and setting collar as I…Continue

Started by Heather Mesa in Beginners' Zone. Last reply by Ken Kortch on Saturday.

Hanging Project Center

Has anyone found a good solution for hanging the Kreg Project center when it is not in use?Continue

Started by EJ Kenney in Beginners' Zone Sep 4.

Product Reviews

My K4 Master System

I picked up the K4MS from Home Depot about 3 months ago, I was looking for a small filing cabinet for under my desk and nothing I looked at would fit or they wanted big money for it, my wife said “why don’t you just build your own then you will…

Continue

Posted by Randy W. Lush on August 25, 2019 at 12:30pm

K5 Review

I really like the k5 it is faster to change from different size of screws. I hesitated to update because of some of the reviews about the dust collection hook up. That to me one of the improvements it works perfect no dust to cleanup .…

Continue

Posted by Gary roofner on April 5, 2019 at 10:02am

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_