Kreg Owners' Community

When it comes to using something to help with keeping cross cuts and rips straight, what do you prefer to use and why?  

Bora

Rockler

Peach Tree

Or a homemade plywood/straightedge jig

This is assuming you would be using a circular saw or jig saw and do not own a table saw.

Views: 1419

Reply to This

Replies to This Discussion

Ken,
It's also a design issue. The pivots on my base are so flimsy, that they cannot be calibrated with certainty. Adjustment must be made with a hammer or a pry bar.
Good enough for house framing, but not for house cabinets.

"Bora

Rockler

Peach Tree

Or a homemade plywood/straightedge jig"

Only difference I can see in the first 3 is the color. The obvious advantage of the last one is initial cost. I have a Harbor Freight that I like because the Peachtree and Rockler clamps I have don't always have enough motor clearance on deeper cuts where the Harbor Freight has a lower profile.

As has been pointed out, those guides are as good as your saw. I have an old Milwaukee drop foot (no pivot points) that is dead on. I don't think they make that saw anymore, go figure. The down side to the saw is that it doesn't work well with the Eureka track system so I picked up a Makita track system. I was going to spring for the Feestool but at the time, the Feestool were under a recall, and sales of the TS55 had been suspended. No matter, I'm more than satisfied with the Makita.

Here's my 3rd generation 96in long "shooter board" for my Makita circular saw.  Note how thin it is -- the thicker it is, the less it can cut your work.  Note how wide it is -- you want the motor housing to clear the clamp on the left side, and being wider makes it stiffer.  I also glued it up to be slightly concave over the length, that way the center presses against my work as the two ends are clamped.

The saw base is only 1/8th in thick, so one advantage of this shooter board is that the saw base cannot go under the edge guide.  Waxing the aluminum base helps it glide along.  Another advantage of a shooter over just an edge guide is that the saw rides on top, so it does not scratch what you are try to trim (like nice finished doors.)

The cost was free.  I used leftovers of that good 1/4in underlayment (with X's all over as targets for stapling) from Lowe's for vinyl flooring, and glued the pieces together.  The only critical part of assembly is that the saw base right side guide edge must be perfectly straight (1/32" or less) over the entire length.  The bottom guide is left oversized and is trimmed after assembly.

A cool trick I use on my straight edge is spray glue the non slip pad you use under a rug for hard wood floors. Doesn't slip no need for clamps.

Rick,

The saws, I made reference to in my previous post, 

contained a HD thick base ---

the rear pivots are of a thick cross-section---

the forward pivots and clamping were substantially sturdy---

Much more rugged construction over the less expensive saws.

Thus the reason for my selection of the saws.

(These are HD construction rated saws).

Upon evaluation of the saw blade alignment, it was concluded the front and read "pivot" were not aligned.

Perhaps out of spec by .03-.04.

The pivots were not flimzy, they couldn't be adjusted using a hammer and pry-bar.

The forward mounting base holes, would have to be relocated, so as ot align the pivots.

(I discussed this matter with another person, who had experienced the same issues, and he had his saw reworked by a machinist.  He had access to a well equipped machine shop). 


Rick said:

Ken,
It's also a design issue. The pivots on my base are so flimsy, that they cannot be calibrated with certainty. Adjustment must be made with a hammer or a pry bar.
Good enough for house framing, but not for house cabinets.

At the time I bought it, the Makita was one of the nicest circular saws available.  It went up against the Milwaukee -- which was heavier, but had the "drop-foot" design, which explains why it remained "dead-on" as John S. notes.  It's still a great saw, but it was designed for durability and not accuracy.

In those days, I never heard of Festool or track saws, which shows how the industry has changed.  Now whenever I watch shows like This Old House, that's all they use is Festool any more.  They are the leader, and others are now copying them -- e.g. track saws, stackable containers, brushless motors, etc.

Either I got lucky or the cheap bosh at Lowes is still a good saw mine is dead on with an edge guide. Think I paid $59. You might try that saw or there is write up about the grizzly tracksaw works well by doing a couple of things shorting the spring because the tensioning is to tight. The other thing was on the track there are two support strips that support the saw and on the grizzly they mounted near the middle of the track. If you carefully temove the strips and move them to the outside edge of the track the saw is stable and works properly. If i get chance I'll find the you tube link.

Here is the link Your talking about a tracksaw with 8 ft capacity for $300.

http://www.youtube.com/watch?v=vqqcmC5UY5E

Thanks for the info, Gary.

Problems will be solved as soon as Kreg introduces a "track saw".

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_