Kreg Owners' Community

Hi.  My son and I am building some cabinets to hold some band instruments for the local school (an Eagle Scout project).  We are using 3/4" baltic birch plywood (60" x 60" pieces) and Kreg pocket screws (we have the DB210 foreman).  Here is a link to a drawing for the first of 6 cabinets. 

https://www.dropbox.com/s/u4cojaa3k92ag30/cabinet 5 - Pub.pdf?dl=0

This one just has three cubbies.  Some others will have more.  On this one, everything is cut and most pocket screws and biscuits cut/drilled as well and we are near ready for assembly.  We are going to glue the tops and bottoms to the sides and back.  We are debating on gluing the sides to the back or just keeping that dry with the pocket screws.

Assembly sequence is to assemble the lower cabinet by laying the back down flat and then start to assemble all with clamps, screw the sides to the back, then we can unclamp and glue and screw the top and bottom on.  The middle shelf will go in with the sides.  No biscuits on this.  Just screws and some glue.

After the lower cabinet is done, we will then assemble the upper cabinet in a similar way and then once that is assembled, screw the upper cabinet to the lower cabinet.

Note  we have an upper and lower cabinet since the baltic birch we can get is 60" square.  There will be no face frame and we will slightly round over the inner edges.  I have done that on another project and end of the baltic birch looked good.  We may add a little platform in the room to raise the cabinets off the ground.

The drawing shows the spacing of the pocket screws.  From the front, the first one in will be 2" from the edge. 

However, since the top of the lower cabinet and bottom of the upper cabinet share the top/bottom, I think we need to offset the pocket screws and any biscuits.  We are looking at making the first one 1.5" from the edge so the upper and lower cabinet screws are off set.  This is noted in the yellow text box in the drawing.

Question 1: is the first pocket screw at 1.5" from the front too close to the edge?  This is connecting the upper cabinet to the lower.  This provides a 1/2" offset of the lower and upper pocket screws.  I tried on some scrap baltic birch and seemed ok.  Is 1/2" offset enough?

Question 2: Any issues with pocket screws going into a glued biscuit (after glue is set up)?  I assume not but figured I would ask.

Question 3: In that shared piece (top/bottom), on the sides and back, we will have two biscuits connecting the lower side and one on the opposite side but offset connecting the upper side.  I am assuming since since we are gluing the biscuits in, that is not an issue and not too many biscuits.

thanks,

Mike

Views: 395

Reply to This

Replies to This Discussion

Hi Mike,

Please contact our team at 800-447-8638 or kregtool.com/help - They will be happy to advise you with this.

Thanks!

I tried the kregtool.com/help and also emailed several times a few weeks ago and no response.  I will try and call.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

First time I really had a need for the ACS miter guide.

I've been using my Adaptive Cutting System table for a few years now, and it's been really solid. This past week was the first time I ever needed to use the miter guide though.I was rebuilding some shelving in a tiny closet and I discovered the…Continue

Tags: ACS

Started by Adam in General Woodworking May 6.

What thread and size screw to use 2 Replies

I am building a small trunk for a military friend to put some belongings in. I have made legs out of ash hardwood and will make the sides out of 1/2” or 3/4” Baltic birch plywood. The legs are 1.5” thick by 2” wide. So since I’m drilling pockets in…Continue

Started by Mike Bohannon in Beginners' Zone. Last reply by Jay Boutwell Apr 19.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2022   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_