Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
Kreg Micro Pocket Drill Guide Compatible ScewsI just received a Kreg Micro Pocket Drill Guide as a gift. Very nice. I read through the instructions and the card that came in the packagi… Started by Ken Kortch |
1 |
Aug 16, 2013 Reply by KregCS |
Kreg Jig HD Drill BitPurchase the Kreg HD jig and started using it last weekend. Drill approx 25 holes, when the tip of the drill bit broke off. Had my drill on… Started by Wally Reed |
8 |
Apr 29, 2013 Reply by Wally Reed |
How many pocket holes per boardI am either making two benches and a table OR adding to my scrap pile. Regardless, I would like to know how far apart to space the holes fo… Started by Debora Cadene |
3 |
Apr 26, 2013 Reply by Debora Cadene |
What is the spacer bar for?I have the M4 and when I watched the video that it came with, it shows them adding the spacer bar right away. Does it have to be there all… Started by Debora Cadene |
14 |
Apr 22, 2013 Reply by james wilhelm |
Decking posts with pocket holesI know it wouldn't be the strongest method in the world, but has anyone used pocket holes to secure the posts used to make a deck railing.I… Started by Steven Power |
5 |
Apr 19, 2013 Reply by Derek Gould |
Use pocket screws as clamps in M&T Joint?Hey folks, I was wondering if the clamping pressure from two pocket screws would be sufficient enough to hold a glued up mortise and tenon… Started by Jason Watkins |
5 |
Apr 18, 2013 Reply by KregRep |
Corded Drill Recommendations?Looking for recommendations for a corded drill for use mainly with the Kreg jig. My requirements: top speed of at least 2500 rpm reversibl… Started by KregBrady |
7 |
Apr 5, 2013 Reply by Russ Haynes |
Depth collar adjustment confusionI just bought a Kreg jig and I am a little confused by the depth collar adjustment. On one side it has marks for 1/2, 3/4, 1-1/4, 1-1/2 and… Started by Steve Berto |
2 |
Mar 4, 2013 Reply by Brian Spencer |
Modification to clampI cut small squares of cushioned white vinyl shelf liner and attached to the face of the clamp with 3M spray adhesive. After it dried a co… Started by George Stoltz |
14 |
Feb 23, 2013 Reply by Ken Darga |
micro jig issuesI recently bought the micro jig for 1/2 inch material. I've never got it to work correctly and I've followed the directions to the letter.… Started by Tony Lawson |
34 |
Dec 9, 2012 Reply by Chris Traver |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service