Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
K4 on steroidsCheck out this guy's modification to his K4! Not sure if this has been posted before or not. K4 with Foot Operated Clamp Started by Jason Watkins |
2 |
Dec 5, 2013 Reply by Gary roofner |
Screws showing through!I am pretty upset about this and need some help figuring out what is wrong. I am using the jig according to instructions. I have 3/4 think… Started by Tim |
15 |
Nov 26, 2013 Reply by ray vile |
Pocket Hole troubleshooting...Experts please weigh in!Hi all, Below is a picture of an issue I am having recently. This is a picture of pocket holes in 3/4 oak. In a softer wood the issue, l… Started by Justin |
8 |
Nov 13, 2013 Reply by Raymond Buitron |
Kreg Drawer Rail Suggestions for First Time UsersI just used the drawer rail jig for the first time this week and have a couple of tips to share. The drawer rail jig took a little bit to g… Started by Bryan Patrick |
1 |
Nov 5, 2013 Reply by Ken Darga |
RE: the Deck Jig..... your thoughts please?anyone used that deck jig with soft redwood and/or cedar decking? how about with very old dry redwood and/or cedar decking??? ....heard th… Started by Jim Covington |
3 |
Nov 3, 2013 Reply by Derek Gould |
Strait cut last few inches on rip cutHello everyone, I was wondering if anyone had tips or advice on how to get a strait cut during the last few inches of the rip cut. It se… Started by Scotty Gadlin |
18 |
Nov 3, 2013 Reply by Derek Gould |
Lost my holeWhen I first got my jig it gave me deep pocket holes enough to clamp my 90 ph clamp now there is no hole at all and my clamp won't grip - a… Started by Dale Newton |
12 |
Oct 23, 2013 Reply by Dale Newton |
Small work spaceI am currently building a fairly small bed frame for my Grandaughters doll. The problem is: the bed is kind of narrow, and when I get to t… Started by Ron davey |
6 |
Oct 5, 2013 Reply by Matt Terry |
Rip Cut questionThis may have been discussed elsewhere but I cannot find it so here goes. How much should I add to the depth setting on my circular saw w… Started by Scott Aldridge |
14 |
Oct 4, 2013 Reply by Ken Darga |
Revised Kreg Jig Table for Different Material ThicknessesA while back I had downloaded a PDF file of a table with jig settings and screw lengths for different thicknesses of materials - I think I… Started by Ken Kortch |
3 |
Oct 3, 2013 Reply by Ken Kortch |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep.
Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service