Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
Using pre-stain liquidI plan to use Minwax pre-stain conditioner. If I understand the directions I can apply stain within 30 minutes after wiping off the exces… Started by George Stoltz |
4 |
Jan 31, 2013 Reply by Ken Darga |
Using Kreg wood plugsDoes anyone have any suggestions or tips for working with Kreg wood plugs? Do the plugs have to be sanded flush? Started by George Stoltz |
5 |
Jan 30, 2013 Reply by Ken Darga |
pine knobsDoes any one know where to get small pine knobs, for jewlery box drawers ?? Started by steven michaud |
2 |
Jan 30, 2013 Reply by steven michaud |
Smooth driilingWhat is the best way to drill smooth 1 1/2 inch holes in 3/4 inch lumber? Started by Kelly Peterson |
3 |
Jan 28, 2013 Reply by KregRep |
Attaching solid oak to veneer plywoodMy first project includes attaching solid oak pieces to veneer plywood. Am I correct in assuming that I would use the Kreg screws with a f… Started by George Stoltz |
5 |
Jan 27, 2013 Reply by Tom Moores |
First project should I assemble or stain and seal and then assembleHello, New to the site and just got my Kreg jig today. I am making a combination book case/wine storage unit. Am using veneer plywood. … Started by George Stoltz |
9 |
Jan 25, 2013 Reply by George Stoltz |
My first projectHello, I am new here as well as to DIY works. I bought a Kreg Jig on e-bay and started on my first project, a christmas gift for my wife,… Started by Carlos |
10 |
Jan 24, 2013 Reply by VICTOR REYES |
table vs radial sawFYI http://www.bobvila.com/articles/492-table-and-radial-saws/pages/1 Started by Ken Darga |
20 |
Jan 22, 2013 Reply by Jason Watkins |
Veneer vs Buying PlyStarting a vanity soon, not a very big one. maybe 48" long single sink. Just wondering if I should by veneered plywood, or just veneer it m… Started by Matt |
7 |
Jan 22, 2013 Reply by Matt |
Radial Arm SawWhat are the benefits of having one of these in your shop? I have a 12" dewalt sliding miter saw. I have never used a radial arm saw befo… Started by Jerrod McCrary |
18 |
Jan 22, 2013 Reply by Jason Watkins |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service