Kreg Owners' Community

First project should I assemble or stain and seal and then assemble

Hello,

New to the site and just got my Kreg jig today.  I am making a combination book case/wine storage unit.  Am using veneer plywood.  

Should I assemble the unit before finishing and then take it apart to stain and seal and then put back together.

The staining and sealing steps would be easier and look better if I could do each piece flat.  What do you gals and guys do?

Views: 2289

Reply to This

Replies to This Discussion

I've done it both ways.

For most projects it's better to seal, stain and finish after the object is assembled.

Finish the pieces ''before'' assembly , if they're items that will be bolted in-place,

such as stained piece affixed to a painted object., or visa-versa.

Well  George Stoltz I build drasser's and I have a problom with my ply running and been thanking about that too. I pre stain some parts be fore I put them togather but it's a idel.

I use ''sanding sealer'' before applying stain, so as to get a more even finish blend.

IMHO, it may depend on what you are making. Chairs, for example, may not matter but for furniture that has a panel, I would stain, seal, assemble, then finish. That way, as the wood moves, I don't see unstained wood in any gaps.

I use sanding sealer,too.  I have become accomplished at mixing and matching stains.  It's just the cutting of wood and building where I am a novice. 

My practice is to never satin and seal anything that is part of a frame or main structure of a project.  My reasoning is that stain and sealer fill up the wood grains and somewhat hinders the penetration of any glue.  One exception to this is on cabinet doors where it stain the edges that go into the groove as the panel should free float with in the door frame and sometimes will show bare wood should the panel move too much.  Although I also use space balls and panel alinement strips in the grooves to control movement and keep the paned centered in the door frame, there is occassions when the panel will move enough that it could show bare wood on the panel edges. i never assemble something and then take it apart to finish it and then reassemble it as you are doing twice the amount of work and again any edges to be glued will suffer from lack of good glue penetration. 

Then you have tackled the most difficult part first.  ;-)

George Stoltz said:

I use sanding sealer,too.  I have become accomplished at mixing and matching stains.  It's just the cutting of wood and building where I am a novice. 

I have learned the hard way, trying to finish After. If you finish before its together you"ll have better angles and access to your project. If you finish after its together, watch out for your glue squeeze out. Glue will seal the wood very quick. And you'll see blotches were you either smeared the glue. or just didn't get it soon enough. Good Luck!

Shawn,

I agree even though this is my first project.  I am doing a "dry assembly" without stain.  then I will take it apart and finish the wood.  I can do a vastly better job on stain and poly when the pieces are separate.

Thank you for your input.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_