Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
1st use of Kreg JigSo I have spent the last 3 days cleaning my garage which has been used for storage for almost 3 years after moving into our home. The gara… Started by john jordan |
11 |
Jul 19, 2012 Reply by Pierre Vallee |
DADO BLADE SETSDoes anyone know the difference between the Avenger AV-10026 and AV-84206 Dado Sets. I can't find any difference, but there must be with 2… Started by Michael Coughlin |
1 |
Jul 15, 2012 Reply by John Schaben |
Light houseDose anyone one have plans for a nice lighthouse Started by Chris Wright |
5 |
Jul 13, 2012 Reply by Chris Wright |
Joining 3/4" oak into 1-5/8" oakAnyone have advice for joining a piece of 3/4 oak to a piece of oak 1-5/8"x1-5/8"? I need a fine thread screw, but it seems that the fine t… Started by Paul Carey |
4 |
Jul 12, 2012 Reply by Rick R |
1/2" Plywood for drawersI am planning on buying a K4 Master System with a couple of clamps to begin with. Also getting the Kreg Rip-Cut. I am fairly new to buildin… Started by Chad |
10 |
Jul 11, 2012 Reply by Ken Darga |
I need help to find help in making a 6 poiont deck floor to put gazebbo on can anyone email me the below?My name is James Reeves, from Ontario, Canada l am not so good at designing yet can't work google program. Just had a stint pout in main ar… Started by James Reeves |
1 |
Jul 7, 2012 Reply by John Schaben |
Laminate, Wax, Seal and MDFI wanted to build a small general use table for my kids but seeing that they are kids... it's going to get wet and that's a problem. I hav… Started by Steve Kwon |
11 |
Jun 28, 2012 Reply by Gary roofner |
Attaching apron to legs - pocket holes or steel braces?Attaching 4x4 legs to a 2x4 apron on a 7 ft table. Is either of these solutions significantly better than the other ...? A) 2 or 3 pocket… Started by Shift |
9 |
Jun 24, 2012 Reply by Shift |
How to fix up table topJust finished putting together a 7' table top using 2x6 pine. It's the first table i've ever built, so I'm learning as i go, and making… Started by Shift |
3 |
Jun 23, 2012 Reply by Ken Darga |
Dado Blade setsI need to buy a dado Blade set. Am looking for help in what to buy. Looking in the under $100.00 cost. All suggestions would be helpful. Am… Started by Michael Coughlin |
5 |
Jun 22, 2012 Reply by Ken Darga |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service