Kreg Owners' Community

Jack Julius
  • 57, Male
  • Edgewater, MD
  • United States
Share on Facebook
Share

Jack Julius's Friends

  • KregRep

Jack Julius's Discussions

New here...
7 Replies

I think this is my first time chatting here. I own a few Kreg Jig products. Love doing DIY stuff. Totally remodeling my kitchen, tore down a wall, put up 2 LVLs, did all the drywall and electrical…Continue

Started this discussion. Last reply by KregRep Dec 18, 2017.

 

Jack Julius's Page

Latest Activity

KregRep replied to Jack Julius's discussion 'New here...'
"Technical Support will be happy to help with this. You may reach them at technicalsupport@kregtool.com or toll-free 800-447-8638. Thanks!"
Dec 18, 2017
justin waldron replied to Jack Julius's discussion 'New here...'
"Are you sure there aren't pocket holes holding that piece of faceframe in that you could just unscrew and run it through the table saw?  Your guide will certainly work if there aren't.  "
Dec 18, 2017
Ken Darga replied to Jack Julius's discussion 'New here...'
"CLear packaging tape will suffice---cover the areas that the saw will ride on. Whe complete, just lift and peel off the tape.  "
Dec 17, 2017
Jack Julius replied to Jack Julius's discussion 'New here...'
"I  decided I was going to make a fence, so I wouldn’t scratch the face frame.... hopefully this will work. "
Dec 17, 2017
Jack Julius replied to Jack Julius's discussion 'New here...'
"Here is the oven cabinet... These  were spaces for slide out drawers.  I’m adding two separate ovens, and the warming drawer at the bottom. The first oven already has a base and I have to create new base for the metal and raise the…"
Dec 17, 2017
Ken Darga replied to Jack Julius's discussion 'New here...'
"Look into the mini angle circular saws, that uses 3-1/2 to 4" blades. Also a good jig saw, may suit your needs.   You won't be able to make the cut up tagent to an inside corner, with either; however, you could finish the cut…"
Dec 17, 2017
justin waldron replied to Jack Julius's discussion 'New here...'
"Assuming you just need to trim a faceframe, you may be able to completely remove the frame and make the cuts on the table saw, you could cut that portion of faceframe out and add a new piece or my final suggestion would be to use a track saw/jig saw…"
Dec 17, 2017
Jack Julius posted a discussion

New here...

I think this is my first time chatting here. I own a few Kreg Jig products. Love doing DIY stuff. Totally remodeling my kitchen, tore down a wall, put up 2 LVLs, did all the drywall and electrical and now putting in cabinetry. Oh also did the tiling. Closed up a doorway into the kitchen where the washer and dryer was, turn them towards the hallway.Took almost a year and a half to remodel my kitchen because of problems underneath the house that I had to fix as far as leveling/settling goes.…See More
Dec 16, 2017
Jack Julius posted a status
"I think this is my first time chatting here. I own a few Kreg Jig products. Love doing DIY stuff. Totally remodeling my kitchen."
Dec 16, 2017
Jack Julius is now a member of Kreg Owners' Community
Feb 5, 2010

Profile Information

Which Kreg products do you own?
Kreg Jig K5/K5MS, Kreg Jig R3 (Jr.), Accu-Cut, Rip-Cut
How would you describe yourself?
Intermediate DIYer
How did you learn about the Kreg Owners' Community?
kregtool.com
What's one interesting fact about you, your life, your garage, shop, or home?
I’m very creative and always strive to create something on a daily basis.

Comment Wall

You need to be a member of Kreg Owners' Community to add comments!

Join Kreg Owners' Community

  • No comments yet!
 
 
 

Need Help?

For Technical Support, call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 

Videos

  • Add Videos
  • View All

Forum

1x6 into a 4x4? 1 Reply

Started by Dave N in Kreg Jig® Projects. Last reply by Ken Kortch 16 hours ago.

Rip-Cut Ruler 4 Replies

Started by Cynthia Alaniz in Beginners' Zone. Last reply by KregCS Sep 19.

Concealed hinge jig 1 Reply

Started by Michael B in Kreg Jig® Operation. Last reply by Edward Weitsman Sep 19.

Pocket screws to attach table tops 1 Reply

Started by Joe L in General Woodworking. Last reply by Glen S Sep 4.

new member

Started by Al Baker in Beginners' Zone Aug 30.

Product Reviews

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 4 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am

© 2018   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_