Kreg Owners' Community

Dan Duce
  • Nova Scotia
  • Canada
Share on Facebook
Share

Dan Duce's Discussions

Accu-Cut: Set Screws in Track Keep Coming Loose
1 Reply

Hi Folks,Just wondering if anyone has had problems with the set screws in their Accu-Cut track?  I just used my newly purchased system yesterday for the first time.  It takes a little getting used…Continue

Tags: accu-cut

Started this discussion. Last reply by KregRep Jan 22, 2018.

 

Dan Duce's Page

Latest Activity

KregRep replied to Dan Duce's discussion 'Accu-Cut: Set Screws in Track Keep Coming Loose'
"Hi Dan, Technical Support will be happy to help with this. You may reach them at technicalsupport@kregtool.com or toll-free 800-447-8638. Thanks!KregRep"
Jan 22, 2018
Dan Duce replied to Bigchief's discussion 'Full size bed'
"Yeah, Justin's method is what I use, too. Always start with the mattress size and make sure you design in room to actually be able to get the sheets on the bed once it is built. If you are using a flat surface for the mattress then this…"
Jan 22, 2018
Dan Duce replied to A Kain's discussion 'attaching track saw to Kreg Rip-Cut'
"Hi Dave, I like the way you think!   I'm always trying to find easier ways to save steps on repetitive tasks. I don't think what you're describing here would work though.   If I'm reading you correctly, you…"
Jan 22, 2018
Dan Duce replied to daddywoofdawg's discussion 'Pocket hole tearout'
"Hello, In that same situation, I've put screws in both ways, depending upon which way would make them harder to see.  For example, if the cabinet is against the wall then I'll put them in from the outside edge so you do don't…"
Jan 22, 2018
Dan Duce replied to Matthew Hinton's discussion 'Is my drill speed set too high when screwing?'
"Hi Matthew, Based on my experiences I'd say there are a few possible culprits. 1. Wood is wet and soft.   - I've noticed screws will dig deeper through pine, especially if it is fresh 2. Drill clutch setting / speed is too…"
Jan 22, 2018
Dan Duce posted a discussion

Accu-Cut: Set Screws in Track Keep Coming Loose

Hi Folks,Just wondering if anyone has had problems with the set screws in their Accu-Cut track?  I just used my newly purchased system yesterday for the first time.  It takes a little getting used to, but after a while I started liking it more and more.The only real complaint I have with the system is that the set screws used to hold the two sections of track together are constantly coming loose, to the point where they fall out when you pick up the track.Is anybody else having this problem? …See More
Jan 22, 2018

Profile Information

Which Kreg products do you own?
Kreg Jig®
How would you describe yourself?
Intermediate Woodworker
What's one interesting fact about you, your life, your garage, shop, or home?
My wife and I design and build everything together.

Dan Duce's Photos

  • Add Photos
  • View All

Comment Wall

You need to be a member of Kreg Owners' Community to add comments!

Join Kreg Owners' Community

  • No comments yet!
 
 
 

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Adaptive Cutting System

I really like the Adaptive Cutting System (ACS) and hope to buy it soon. My table saw really scares me as I have a bad knee that likes to buckle on me at inopportune times. I can just picture it happening at the table saw and tossing me into the saw…Continue

Started by Marshall Harrison in Beginners' Zone on Tuesday.

Ulimate K4 3 Replies

I really like my K4 pocket hole jig but I had a big cabinet project coming up so I wanted a way to clamp the boards to it faster than the toggle clamp alowed. I had seen some other people make pocket hole jigs with pneumatic cylinders in place of…Continue

Tags: k4, Pneumatic

Started by Iain Portalupi in Kreg Jig® Projects. Last reply by Marshall Harrison on Thursday.

Octagonal picnic table 2 Replies

Any plans available? Worked with wood before. Just got my Kreg5. Have a camp in the Adirondacks. Workshop there.

Started by MICHAEL FLANAGAN in Beginners' Zone. Last reply by MICHAEL FLANAGAN yesterday.

Farmhouse Table Plans 2 Replies

Dear Kregeers,I would like to try and build a farmhouse table with extensions in the middle to seat 12.I have seen some plans on Ana White and Buildsomething, along with others. Unfortunately, most, if not all the plans are for extensions at the…Continue

Started by Lupe in Beginners' Zone. Last reply by Lupe Feb 12.

Product Reviews

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 5 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am — 2 Comments

Kreg Foreman

I have built many kitchens and finally decided to buy the Foreman, because my latest kitchen consisted of 28 cabinets and I was over my hand hurting from all the drilling, moving the clamp etc., it seemed like a smart choice.

The…

Continue

Posted by justin waldron on January 8, 2018 at 4:05am — 2 Comments

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_