Kreg Owners' Community

Shuffleboard table

9' shuffleboard table with 8' playing surface.

Box has common pine sideboards and the bottom (not seen) is plywood and mdf scrap.

Playing surface is 2 x 3/4 birch plywood with red mahogany stain. The surface is not attached yet - I may redo it b/c the stain is so dark, the scoring lines are hard to see.

Vinyl liner for the inside of the box. Glued using Weldwood contact cement.

Steel pipe for the legs. Go to Essential Hardware for best prices.

  • photo
  • photo
  • photo
  • photo
  • photo
  • photo
  • photo

Comment

You need to be a member of Kreg Owners' Community to add comments!

Join Kreg Owners' Community

Comment by Tito Comas on November 11, 2017 at 2:41pm
Hi Andy, I just have a few more questions about your table. How long are the legs? What width are the sides of the box? Thanks for your help.

Tito
Comment by Andy Wilson on October 19, 2017 at 10:31am

No plans - sorry - I really just kind of built it on the fly.

The playing surface is 3/4 in birch plywood - I took two sheets 16" wide by 8 ft long and glued them to create the 1 1/2 thick playing surface. I then used fiberglass filler to smooth the edges to paint black. 

I actually created a new playing surface later - the dark stain on this one was too dark to use number decals. I'll post a new pic. I used Edge Glued Finger Joint Pine Board from lowes - 8 ft with a thick glaze coat finish. The playing surface needs to be thicker than 1 1/2 inches so you may want to go with 3 boards thick.


The box - i just winged it - I made it 12 inches longer and 8 inches wider than the playing surface to give room for the pucks to land. The base of the box and sides are covered cheap vinyl from Walmart. I glued the vinyl to the bottom and sides using vinyl pieces that were about an inch larger than all of the boards so that the overhang could be tucked and trimmed - before building the box.

The legs are cast iron pipes spray painted with oil rubbed bronze rustoleum metal paint.

I bought the pucks and sliding dust on Amazon

More expensive tables have hardware underneath to slightly bow the playing surface to make it just very very slightly concave to keep the pucks on the surface more. I'm looking to do that eventually.

Comment by Tito Comas on October 19, 2017 at 9:48am

Hi Andy, I love your shuffleboard table!! Do you have any plans/drawings you can share with me as I would like to make one!! I live in Ottawa and am not familiar with Essential Hardware; where do you live?

Need Help?

For Technical Support, call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 

Videos

  • Add Videos
  • View All

Forum

Missing clamping table project 3 Replies

Started by Brandon B. in Beginners' Zone. Last reply by jock sloan 23 hours ago.

90 gallon aquarium stand

Started by Glenn Gilbert in Community-Specific Jun 11.

Proper clamping technique 1 Reply

Started by Ron Salgado in Kreg Jig® Operation. Last reply by KregRep May 31.

Edge joining 3/4 inch plywood 2 Replies

Started by Lynn Greff in Beginners' Zone. Last reply by Lynn Greff May 20.

Where can I get a K3 owners manual.... 3 Replies

Started by John Chasse in Beginners' Zone. Last reply by John Chasse May 19.

Product Reviews

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 4 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am

© 2018   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_