Kreg Owners' Community

Hi all,

          I'm planning my first project, the potting bench and my wife is short.

I want to make it a couple inches shorter and figure taking it off the top of the Front legs(A) and the top of the back legs(B) should do it. 

Am I missing anything???

Views: 153

Reply to This

Replies to This Discussion

Thomas,

Without knowing what set of plans you're using let me offer the following: If the back legs extend upward past the work surface height , supporting shelves, taking inches off the top of each will not work, unless you adjust the height the rear of the work surface mounts to.  If all four legs only support the work surface portion of the bench then taking an equal amount from each would work.  Another option is to take inches off the bottom of the legs and adjust the height of the bottom shelf upward by a similar amount.

Hope this makes sense, Don

Thanks Don,

                      I am using the Kreg plans for my bench if that helps anyone with my question. 

Reply to Discussion

RSS

Need Help?

For Technical Support, call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 

Videos

  • Add Videos
  • View All

Forum

LED Lighting on mobile bench

Hi AllJust got myself a new Metabo mitre saw, kitted it out with a new Freud Pro blade as well as "pimped up" my bench with LED lighting so I can find stuff! I have 22 LED daylight tubes in my fittings in the garage so there is more than enough…Continue

Tags: blade, mitre, saw, lighting

Started by Steven Baynes in Miscellaneous Oct 8.

Ridgid tools 1 Reply

I originally bought Ridgid tools for the warranty, well I had to replace batteries. Very easy and got new batteries and chargers. Found out they don't make 24 volt tools any more, so I sent in a hammer drill, impact driver and light for replacement…Continue

Started by steve kidd in Beginners' Zone. Last reply by Glen S Oct 9.

Cabinets and the best wood choice for the carcass. 3 Replies

I am going to try and new project.  Never made cabinets before.  Researched and You-tubed like crazy.  So many opinions.  Mine are going to be:1 each= 30"W x 14"D x 38"H2 each =29"W x 14"D x 38"H1 floor to ceiling cabinet 18"W x 24"D and the height…Continue

Started by Stephanie H in Kreg Jig® Projects. Last reply by Glen S Oct 2.

1x6 into a 4x4? 4 Replies

Perhaps this question has already been asked somewhere on this forum but I wasnt able to find it after an hour or so of searching. Is there a recommended length of Kreg screw to use when combining a 1x6 into a 4x4 post. I have seen a few conversion…Continue

Tags: size, screw

Started by Dave N in Kreg Jig® Projects. Last reply by Edward Weitsman Sep 29.

Product Reviews

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 4 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am

Kreg Foreman

I have built many kitchens and finally decided to buy the Foreman, because my latest kitchen consisted of 28 cabinets and I was over my hand hurting from all the drilling, moving the clamp etc., it seemed like a smart choice.

The…

Continue

Posted by justin waldron on January 8, 2018 at 4:05am — 2 Comments

Kreg K5 Jig Review

Posted by Daris R. on November 20, 2017 at 5:39pm

© 2018   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_