Kreg Owners' Community

E M Hampton
  • Edmond, OK
  • United States
Share on Facebook
Share

E M Hampton's Discussions

Driver Bit Issue
11 Replies

Hello All. First of all, I am very pleased with all my Kreg equipment...except for one tiny annoyance. Does anyone else have problems with the square heads of the driver bits rounding off and (then…Continue

Started this discussion. Last reply by Luis Torcida Oct 7, 2018.

 

E M Hampton's Page

Latest Activity

Luis Torcida replied to E M Hampton's discussion 'Driver Bit Issue'
"I would LOVE to have Star heads screws instead. Not a big fan of square bit..."
Oct 7, 2018
Tim Grace replied to E M Hampton's discussion 'Driver Bit Issue'
"Sorry for the delay in response.  The ones I picked up at Rockler were in the store and aren't shown on-line."
Jun 29, 2018
Jamil Samimi replied to E M Hampton's discussion 'Driver Bit Issue'
"EM, aloha~ I too am a newcomer to the system and I'm finding the same problem. I am using a drill (not impact) with the clutch set low and, despite really pressing to get the tip into the screw (and feeling it lock in), I still get some…"
Jun 18, 2018
Glen S replied to E M Hampton's discussion 'Driver Bit Issue'
"The screw wax made driving the screws a whole lot easier!"
Jun 20, 2017
Glen S replied to E M Hampton's discussion 'Driver Bit Issue'
"You're Welcome. I hope that trick works for you. I also bought some screw wax that I'm going to try on a Tiger Maple face frame."
Jun 14, 2017
E M Hampton replied to E M Hampton's discussion 'Driver Bit Issue'
"Thanks, Glen. Will pick some up and try them. Thanks for the drill position tip. Will try it next time I am using the jig. "
Jun 14, 2017
E M Hampton replied to E M Hampton's discussion 'Driver Bit Issue'
"Thanks, KregCS. I do try to let the screw do the work. Since you can't see the screw head and you driving at an angle, it is a bit more of a challenge to align properly. Will try harder, but will also get hardened tips. I am sure I'll…"
Jun 14, 2017
Glen S replied to E M Hampton's discussion 'Driver Bit Issue'
"Mine stripped quickly too. I bought Hitachi bits from Menards & never looked back. Also rather than holding the drill like you normally would with the handle to the left or right. Turn the drill upside down,, cord or battery straight up. Just…"
Jun 7, 2017
KregCS replied to E M Hampton's discussion 'Driver Bit Issue'
"Mr. Hampton,  When driving in your screws you will want to make sure that the driver is fully engaged with the screw head.  Due to the angle the screw is being driven in at, if this is not fully engaged it will greatly increase your…"
Jun 6, 2017
E M Hampton replied to E M Hampton's discussion 'Driver Bit Issue'
"Thanks, Tim. The only ones I see at Rockler, however, are labelled: Kreg Jig® HD Driver Item #: 47983. Are they the ones you ordered?"
Jun 4, 2017
Tim Grace replied to E M Hampton's discussion 'Driver Bit Issue'
"Mine rounded off quite quickly, as well.  I attributed it to using an impact driver to drive the screws, some of which had space restrictions and required awkward angles.  I did pick up a couple at Rockler that had hardened tips and lasted…"
Jun 3, 2017
E M Hampton posted a discussion

Driver Bit Issue

Hello All. First of all, I am very pleased with all my Kreg equipment...except for one tiny annoyance. Does anyone else have problems with the square heads of the driver bits rounding off and (then of course) stripping out? I suspect technique may be contributing, but I also wish they were perhaps a bit deeper and harder. Anyone else have this problem or abe to offer any suggestions? Thanks in advance. See More
Jun 2, 2017
E M Hampton replied to KregRep's discussion 'New Members: Please introduce yourself.'
"Hello. Monty here from Oklahoma. Long time (self-proclaimed) DIYer, but previously more concerned with function over form (admittedly, it showed). Recently retired at 60 and am looking forward to upgrading all my older, contractor grade equipment…"
Apr 25, 2016
E M Hampton replied to Patrick Willyard's discussion 'Universal Bench Top'
"Hello - new to the community. Purchased Universal Bench Kit (64 x 28). Intended use - general purpose mobile workstation. Contemplating using 36 inch solid core door with a white faced hardboard as the work surface. A few questions for…"
Apr 25, 2016

Profile Information

Which Kreg products do you own?
Kreg Jig® K4, Shelf Pin Jig, Universal Bench, Kreg® Routing Systems
How would you describe yourself?
Intermediate DIYer
How did you learn about the Kreg Owners' Community?
KregTool.com
What's one interesting fact about you, your life, your garage, shop, or home?
Equipping shop from scratch.

Comment Wall

You need to be a member of Kreg Owners' Community to add comments!

Join Kreg Owners' Community

  • No comments yet!
 
 
 

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Popular Posts & Projects 

Videos

  • Add Videos
  • View All

Forum

Back with Kreg 3 Replies

After being disappointed with my Kreg Foreman I sold it and got a Porter Cable 560. It was a decent jig and performed with decent results. Then a friend who is also a Kreg dealer told me about the K5.i bought one and set it up. I must say it's…Continue

Started by DaveTinley in Beginners' Zone. Last reply by KregCS on Wednesday.

spam 3 Replies

Did anybody get bs email from Timothy White about Your surname? He said he got my name from here.Continue

Started by Timothy Spoon in Beginners' Zone. Last reply by KregRep Apr 4.

Product Reviews

K5 Review

I really like the k5 it is faster to change from different size of screws. I hesitated to update because of some of the reviews about the dust collection hook up. That to me one of the improvements it works perfect no dust to cleanup .…

Continue

Posted by Gary roofner on April 5, 2019 at 10:02am

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm — 1 Comment

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 5 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am — 2 Comments

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_