Kreg Owners' Community

George Hamm
  • Heflin, AL
  • United States
Share on Facebook
Share

George Hamm's Friends

  • Tyler Couchman
  • Jason Carty
  • Rey Carr
  • KregRep

George Hamm's Discussions

Patio Table plans
2 Replies

 Here are the plans for the patio table.Continue

Started this discussion. Last reply by George Hamm Feb 22, 2013.

 

George Hamm's Page

George Hamm's Photos

  • Add Photos
  • View All

Profile Information

Which Kreg products do you own?
Kreg Jig®
How would you describe yourself?
Advanced Woodworker

Comment Wall (6 comments)

You need to be a member of Kreg Owners' Community to add comments!

Join Kreg Owners' Community

At 11:45am on April 29, 2014, Jay Boutwell said…

Thank you George, I appreciate you comments.  Yes it has been a long time but I am recovering.  Stioll have the double vision in the right ey and have an up coming May 16 eye specialist  to see what they can do for it.  I have missed everyone and being on the site.  I will be back soon with some wood working.  Right not now I am not running any saws that require close tollence cuts but have been doing some woodwork.  I have a bid out on a large china cabinet that I will be doing as soon as the bid is final.  I have been cuttting several hundred feet of base board molding for a finish on a large house.

Take care of your self and thank you again for your nice comment and also for the comment of concern about my health.  I so appreciate it.

At 11:33am on November 30, 2012, james wilhelm said…

Your welcome , keep up the good work !!! JIM

At 5:03am on October 20, 2012, George Hamm said…

Thanks for the info.  George

At 5:35pm on October 19, 2012, Dale Lyon said…

You can get the velvet at most craft stores. I go to Joanns

At 10:48am on July 10, 2012, James Waller said…

I was answering your comment about how I was doing and might have accidently put it on "MY Comments", so go to my page and read it.

At 11:39pm on April 4, 2012, Jay Boutwell said…

You are more than welcome and thanks for the nice complement on my cabinets.  No they went into a customers home.   Raised panel door especially the ones with the arch is somewhat of a mystery to some until they see how to set up and build a door.  I just like to pass along what I have learned over the years building cabinets and furniture for a living.

 
 
 

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Concealed Hinge Jig Setting Confusion

The Kreg Concealed Hinge Jig has a setting for the distance from edge of the door to the nearest edge of the 35 mm cup hole. This can be set as 3, 4, 5, or 6 mm.Later in the instruction there is a table that converts the distance from the edge of…Continue

Started by Ken Kortch in Kreg Jig® Operation Oct 11.

Help with old Rip-Cut(tm)

I have an old Rip-Cut which I bought many years ago but did not set.  I seem to have lost the instructions, if I ever had them.I cannot figure out which bolts are match with the nylon-lock screws.This unit is old enough that the current instructions…Continue

Started by Sean in Other Kreg® Products Oct 4.

Product Reviews

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 1 Comment

Kreg Jig Dust Collection Attachment

1st impression when you hold this attachment in your hand:  "not much to it", Kreg sure is makin' $$ here.



Then I installed it.. perfect fit, leaves just enough room to adjust the setting screw on my K4.



Then the real test, hook…

Continue

Posted by Grampy Meyer on February 23, 2020 at 11:36am

© 2020   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_