Sort by: View
Discussions | Replies | Latest Activity |
---|---|---|
wine rackHas anyone made a wine rack using Kreg system? Started by Dennis Clines in General Woodworking |
2 |
May 25, 2011 Reply by Dennis Clines |
Attaching Kreg band saw fenceI have a 35 year old Delta 14" band saw. It has two holes in the left edge of its table but they are NOT threaded. Will the Kreg band saw f… Started by joel adler in Other Kreg® Products |
3 |
May 24, 2011 Reply by Daniel C Webster |
Question on workbenchSo I am getting ready to tackle my first project, the simple workbench. I am very excited, however I had some questions. I do not have in… Started by Scotty Gadlin in Beginners' Zone |
11 |
May 24, 2011 Reply by John Hardin |
Pilot hole depth problemI built a simple bookcase out of 3/4" ply. I set the depth collar using the gauge on the case. I used 1 1/4" coarse screws. On some holes,… Started by antkn33 in Beginners' Zone |
12 |
May 24, 2011 Reply by Otto Johansen |
There's a possiblem.I also had the same problem. I followed all the directions and tripled checked all my marks. I got to the point where finally,I sough… Started by David Briseno in Kreg Jig® Operation |
0 | May 23, 2011 |
Finishing Plywood EdgesDoes anybody know of a good technique for finishing plywood edges without covering them? Started by Walter Maldonado in Beginners' Zone |
3 |
May 23, 2011 Reply by Mike Camp |
How did they join this do you think?Okay so I am basically tearing into every piece of furniture that I can find to see how it is constructed and joined in my aim of self impr… Started by Alex Shiells in General Woodworking |
5 |
May 23, 2011 Reply by mo khan |
Adjustable, slant-top writing desk?I've seen a writing desk with a top that can be flat, or the writing surface can be tilted to 4 or 5 progressively steeper angles for great… Started by sam karam in Community-Specific |
0 | May 22, 2011 |
Does Deck Jig make stainless screws unnecessary for cedar decking??Normally, stainless screws are used for cedar decking when face screwing to prevent discoloration/staining. Since the Deck Jig drives the s… Started by John Burke in Kreg Jig® Operation |
3 |
May 22, 2011 Reply by John Schaben |
Big Garage Shelves Using KregOver years, garage is full with stuff. My wife and I finally had garage sale last month and we need better ways to store stuff. (Hint: room… Started by Grant Laird Jr in Kreg Jig® Projects |
1 |
May 22, 2011 Reply by Jens Jensen |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service