Sort by: View
Discussions | Replies | Latest Activity |
---|---|---|
tight spot to drill??hey guys how do you drill a pocket hole if you are so close to the wall that the clamp doesn't fit behind it Started by Pat Meeuwissen in Kreg Jig® Operation |
2 |
Sep 20, 2011 Reply by Ken Darga |
combo belt disk sanderI am looking to get a combo belt disk sander that wont cost me a arm and leg any suggestions would be helpfull, thanks Dave Started by david r reasland in Beginners' Zone |
0 | Sep 19, 2011 |
How close to ends of boards can I place a holeHello All, I am new to wood working and the Kreg system, That being said I have a question. How close to the end of the board can drill… Started by Gary Nalen in Beginners' Zone |
22 |
Sep 19, 2011 Reply by Gary Nalen |
Stain producing two diffrent shades..?Hello All, I am fairly new at woodwork and have a slight problem. I have built a headboard and a bed frame. Both were built using the Kre… Started by Derrick Williams in Beginners' Zone |
14 |
Sep 18, 2011 Reply by Bennett S. Reynolds |
Kreg Toolboxx AvailabilityAs earlier noted, when will the 'complete' Kreg' toolboxx become available ? I am a notorious hoarder of most tools, having an extensive… Started by Gordon D'Eri in Other Kreg® Products |
2 |
Sep 17, 2011 Reply by Al Barale |
advice needed on purchasing a multi-toolim looking into buying a multi-tool and what comes to mind would be the dremel http://www.homedepot.ca/product/dremel-multi-max-kit/916712#… Started by Joey in Beginners' Zone |
49 |
Sep 16, 2011 Reply by Edward Van De Car |
New to woodworkerI am Michel Jonson from London, i am new woodworker, please give me some information about this website and its features and its working al… Started by michel jonson in Beginners' Zone |
2 |
Sep 16, 2011 Reply by Al Barale |
Birthday present for my GrandsonIt was my Grandson's 2nd Birthday, so I built this table and chair set for him. All solid pine. Started by Keith Griffin in General Woodworking |
5 |
Sep 13, 2011 Reply by angie brashears |
Cabinet making guideI lost my cabinet making guide from Kreg due to a virus. Had to have my computer fixed and lost everything. Can somebody help me? Started by Roy Orosco in Beginners' Zone |
2 |
Sep 12, 2011 Reply by Bob S |
Kreg cabinet jigI once saw a jig by Kreg to use while installing kitchen cabinets. I have since been unable to locate one or any information about one. C… Started by Gary Hemphill, Sr. in Beginners' Zone |
1 |
Sep 11, 2011 Reply by John Schaben |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service