Sort by: View
Discussions | Replies | Latest Activity |
---|---|---|
Anyone own dust deputy or cyclone?My garage is starting to look like a sawmill My shop vac keeps clogging up Started by Matt H in General Woodworking |
7 |
Sep 9, 2011 Reply by Al Barale |
Pocket hole jig for deck railingHello, I am building a deck from cedar. I used the Kreg Deck Jig to fasten the decking and I'm please with the results. Now I'm just about… Started by John Burke in Kreg Jig® Operation |
4 |
Sep 9, 2011 Reply by John Burke |
what brand router to buy??I'm looking to replace my ryobi router. It does ok for light routing, but i want a router with a little more power. I have been looking at… Started by Derrick Williams in Beginners' Zone |
36 |
Sep 7, 2011 Reply by John Schaben |
I did something stupid - drilled in the wrong placeI am making a nightstand and my plans had very small text that indicated that i was supposed to place a shelf 1 1/2" higher than I actually… Started by Jackie Callahan in Beginners' Zone |
2 |
Sep 6, 2011 Reply by Jackie Callahan |
Screws not tighteningAbout half the time I drive a screw into a pocket hole, the screw bites in and goes into the material, but doesn't tighten down. It'll fre… Started by Anthony Halsell in Kreg Jig® Operation |
32 |
Sep 6, 2011 Reply by eugene knobloch |
Horizontal Router TablesMy turn to ask a question. Horizontal router tables. Good or not so? Any advantages? My reason for asking is several years I worked for th… Started by Rick in General Woodworking |
8 |
Sep 5, 2011 Reply by John Schaben |
Cloths HamperSaw a cloths hamper on a lowes workshop video Wanted to build but can not find it now If anyone can help that would be great Started by Roger William Roden in Community-Specific |
2 |
Sep 4, 2011 Reply by Roger William Roden |
Struggling drill into hardwoodsHas anyone had any problems drilling into hardwoods? I normally build with softer woods and sheet goods but over the weekend I put together… Started by Alex Shiells in Kreg Jig® Operation |
16 |
Sep 3, 2011 Reply by Al Barale |
Routing End-GrainLooking for some advice... I made an end-grain purpleheart/hard maple cutting board from The Wood Whisperer website... (http://thewoodwhi… Started by steven kemp in General Woodworking |
4 |
Sep 2, 2011 Reply by steven kemp |
Multiple Shallow scew holesI'm certain many have already done this , but as a new Kreg user I found this very useful. I was drilling holes in 3/4" boards to just fas… Started by John Goeglein in Beginners' Zone |
0 | Sep 2, 2011 |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service